Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: Fr24feed software Additional FAQs and Info

  1. #1
    Super Moderator
    Join Date
    May 2011
    T-NZCH1, PP:PH New Zealand

    Fr24feed software Additional FAQs and Info

    Feel free to post/discuss on this thread here

    This guide is not to be taken as a representation of officially sourced support information.
    It is contributor-made to assist in answering queries before new threads are created -
    Information has been repeated many times in existing threads but their size deters most readers

    For Flightradar24 supplied HARDWARE please contact support as per supplied information pack/emails

    FR24feed Errors
    Linux/Pi feeder Specific Information
    Beast/Transponder Mouse
    ADSBScope / VRS / RTl1090
    SBS Example
    Web Config Examples

    How does it work?
    The developers have made a package uploader that consists of 3 core parts:
    Direct hardware access files
    FR24 log, filter, bundle and upload data application

    On startup the software will:
    - Scan the configuration file for your setup (answered during install)
    - Evaluate if source connection is native (dump1090 not used) or need software (Dump1090 used)
    - Pass data to be uploadd
    - Output any connection or various errors during startup

    Collecting your data:
    Your data and Hardware will be connected to in 2 ways depending on receiver type:

    - Dump1090 will be loaded and init USB or Com port specified
    - Dump1090 will gather data and make available for FR24feeder to collect
    - FR24feeder will connect to dump1090 output

    - FR24feeder will connect directly to hardware (if readable format output)

    Data is gathered, bundled and sent around every 5 seconds.
    Your status may show 'online' if the connector portion is running, but may not upload data if it cannot connect to specified hardware/ports for data collection
    Status may show offline if no data is collected and sent (bad reception or no traffic)

    There are many reasons incorrect configuration and 3rd party software can cause issues if not configured correctly, So please read further!

    Web Page Configuration - (Fixing startup errors):
    This is the easiest way to check/configure the software when you are sure FR24feed core app is running
    (to fix wizard setup errors found on first run)

    --> http://localhost:8754 <--
    (or replace localhost with the IP address of Rpi or PC running software)

    !You can also edit the config manually - but variable options will need to be known!

    USB DVBT Feeding:

    Dump1090/FR require a Realtek/RTL 28xx chipset, and E4000 or R820 tuner
    FitPower/FC will likely not not work

    Suggested to run FR24feed standalone with no software such as RTL1090 (or Dump1090) present, or any additonal commands such as --interactive as this will cause new or inexperienced users issues.

    To run with other software you must first turn off data-out of other software and FR24feed RAW/Decoded and SBS options to stop conflicts

    ! These MAY be enabled after for more advanced data use again if running certain hardware and are sure nothing will conflict by doing so !

    - Reconfigure/Configure FR24feed to DVBT (or AVR-TCP mode for already running Dump1090)
    - if not already identified on launch add --net to additional commands to enable web output port (8080,30002)
    - Adjust other software data source settings to open AVR/RAW port (added by --net) on localhost:30002
    - Save and restart feeder

    *Running additional software with FR24feed can be complicated. Not all instances or configuration examples can be given due to this
    Ensure you search the following threads for further info from other helpful users:

    Cross Platform
    Raspberry Pi based

    RaspberryPi with FR24feed & PiAware or currently running Dump1090:
    If you have previously installed PiAware separate (or Dump1090) - it may be installed and running standalone. In this instance configure your feeder as AVR-TCP as above NOT USB DVBT or you will face errors similar to error examples below

    AVRTCP config example when running Dump1090/Dump1090-mutability/Piaware/
    *FR24feed Setup Wizard may auto-detect running instance and assist selecting right option
    16-3-16 Developers working on fixing re-sharing of FA data incorrectly

    Other Hardware (not DVBT) Data Relay:

    The options found for RAW/Decoded and SBS data out are valid for other receivers.
    For instance RAW out enabled for a BEAST receiver will open port 30334. While RAW using DVBT config will open 30002
    MPX/SBS out option when used with Kinetic hardware will repeat data on port 20072

    Configure Additional Software:

    Software such as VRS(virtual radar server) and ADSBScope can then be configured to NETWORK data source on those ports
    - You must start with other Server functions of these applications disabled to prevent conflict errors!

    MLAT contacts are server-side triangulated - Source data from Radarcape based receivers + GPS time (Primary) + RPi/DVBT/Dump1090 using NTP time tag (NOT GPS!!) secondary
    RPi MLAT will NOT be enhanced with a USB GPS module
    - due to interface/port transmission speeds adding jitter delays NTP is used for syncronised reference data

    MLAT requires 4+ in-range receivers:
    - Various combinations of Rpi + FR24 receivers contribute (1FR + 3 Pi, 2FR + 2Pi etc)
    - min. 1x FR24 receiver required in combination
    - Overlapping FR24 Receiver GPS-time MLAT prioritised
    - NTP used for commonreference on RPis alongside FR24 data
    - All receivers need to contact the same Mode-S Only aircraft (and 1x ADSB reference aircraft).

    Attributed on the map caclulated from FR24 boxes majority:
    T-MLAT (Europe/Africa)
    T-MLAT2 (North and South America)
    T-MLAT5 (Asia/India/Japan)
    T-MLAT3 (Oceania)

    Attributed on the map calculated from RPi majority:

    FR24FEED Visual Log Checks

    [main][i]Version: 1.0.16-7/generic
    Connecting to Generic receiver via (exe://mr-dump1090.exe  --raw --net --net-http-port 8080)
    Found 1 device(s):
    0: Realtek, RTL2838UHIDIR, SN: 00000001 (currently selected)
    Found Rafael Micro R820T tuner
    Max available gain is: 49.60 dB
    Setting gain to: 49.60 dB
    Exact sample rate is: 2000000.052982 Hz
    Gain reported by device: 49.60 dB
    Breaking this down:
    [i]Version: 1.0.16-7/generic = Current version

    mr-dump1090.exe = Identified as Windows Dump1090 launching
    --raw = RAW time tagging is enabled - this means MLAT option checked
    --net = Advanced network out options of Dump1090 enabled (ports 30002,30003, (30005))
    --net-http-port 8080 = Advanced web output enabled for local radar view on http://localhost:8080

    [i]Connecting to Generic receiver via (exe:///usr/bin/dump1090-mutability  --raw --net)
    Rpi with Dump1090 Mutability (PiAware) installed appears slightly different
    - Dump1090-MR included with FR24 package

    If you are using a DVBT and see an error under
    Found 1 device(s):
    0: Realtek, RTL2838UHIDIR, SN: 00000001 (currently selected)
    See Below post for common issues

    Common Ports:
    Here you can see some examples of software that open live ports if built in options are enabled which can cause conflicts

    FR24 RAW: 30002 (DVBT) / 30334(other hardware)
    FR24 BS: 30003
    FR24 SBS: 20072
    RTL1090 Raw out: 31001
    RTL1090 BS out: 31004
    Kinetic Basestation:
    RAW out: 30006
    BS out: 30003
    SDR: 30005
    AIS: 30007
    SBS3 'standalone' mode: 10001, 30006
    Dump1090 AVR Raw out: 30002
    Dump1090 Beast out (if enabled): 30005
    Dump1090 BS out: 30003
    Dump1090 in: 30001 *

    *Caution with Dump1090 and other software output - it can 'listen' for data on 30001 for multi-DVB or merged feeds and re-broadcasts out 30002. If false positions are feed to this port issues can occur server end

    Some output ports can be tested in the web-browser

    For instance basestation/BS format can often be seen visiting http://localhost:30003

    For others see telnet tests below
    Last edited by Oblivian; 2017-04-09 at 08:42.
    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

  2. #2
    Super Moderator
    Join Date
    May 2011
    T-NZCH1, PP:PH New Zealand
    Asking for help
    If information here is not clear there are some basic things to try BEFORE making a new thread and asking for help.

    If you think you have installed FR24feed and it is running
    - Attempt to load the webpage as described on post 1 to confirm

    - Run above commands to check status
    sudo service fr24feed status

    If service is not running, diagnose WHY
    - Did the installs script fail?
    - Did you complete the install script questionnaire correctly?
    - Check the basic commands
    sudo service fr24feed stop
    sudo service fr24feed start

    Are you unsure of why it will not start or MLAT or other functions are not working
    - Stop FR24feed
    sudo service fr24feed stop
    - Start fr24feed with full output
    sudo fr24feed start ( !! no 'Service' !! )


    If after this you still need help Please help us to help you!
    Receiver type
    OS Platform (Pi/Windows)
    fr24feed version
    Status of fr24feed window
    Config settings (Screenshot of config page)
    Any visible startup errors (screenshot or paste)
    Additional software you may have running (or in the past)
    What checks have been performed to try and fix already

    Common Errors:

    2016-01-26 22:20:05 | [reader][i]Connecting to Generic receiver via (exe://*dump1090*  --raw)
    2016-01-26 22:20:05 | [reader][i]Connected to the receiver, authenticating
    2016-01-26 22:20:05 | [reader][i]Authenticated, processing messages
    2016-01-26 22:20:07 | [reader][i]Connection terminated
    2016-01-26 22:20:12 | [reader][i]Connecting to Generic receiver via (exe://*dump1090*  --raw)
    2016-01-26 22:20:12 | [reader][i]Connected to the receiver, authenticating
    2016-01-26 22:20:12 | [reader][i]Authenticated, processing messages
    2016-01-26 22:20:14 | [reader][i]Connection terminated
    Incorrect configuration set. Check for:
    - USB stick does NOT have the required Realtek RTL28xx chipset
    - Conflicting software locking USB device to 'in-use'
    - Missing zadig driver installation step for windows (cannot read USB devices)
    - Error with additional commands causing Dump1090 to terminate
    - Existing instance of Dump1090 currently running

    2016-01-26 22:20:05 | [bs][i]Starting server on
    2016-01-26 22:20:05 | [bs][e]Could not bind socket to *:30003, errno=0
    The option for Decoded data/30003 out has been enabled. There is already a piece of software with similar option running, locking that port
    - Close other applications
    - Disable "Basestation Out" function on VRS/ADSBScope etc
    - Reconfigure other software output port number

    2016-01-27 00:35:36 | [feed][n]ping 1
    2016-01-27 00:36:06 | [feed][n]ping 2
    2016-01-27 00:36:36 | [feed][n]ping 3
    2016-01-27 00:37:06 | [feed][n]ping 4
    2016-01-27 00:37:36 | [feed][n]ping 5
    2016-01-27 00:38:06 | [feed][n]ping 6
    2016-01-27 00:38:36 | [feed][n]ping 7
    No data is being received by hardware to upload
    - Check connections
    - Incorrect data format received from receiver or software for chosen receiver type
    - Wrong port/type specified from software supplying data

    Found 1 device(s):
    0: Realtek, RTL2838UHIDIR, SN: 00000001 (currently selected)
    Kernel driver is active, or device is claimed by second instance of librtlsdr.
    In the first case, please either detach or blacklist the kernel module
    (dvb_usb_rtl28xxu), or enable automatic detaching at compile time.
    usb_claim_interface error -6
    Error opening the RTLSDR device: Device or resource busy
    USB device in use or blacklisted
    - Follow RPi RTL blacklist How-to guide here
    - Close other instances of Dump1090/RTL1090 or check task manager for running instance
    - Configure other software for Network data (remove exclusive USB need)

    Other Messages:

    2016-01-26 22:20:24 | [raw][i]Starting server on
    Dump1090 set to DVBT and running in --net mode - Raw data port 30002 opened

    "My account status shows online, but no planes or data uploaded"

    This can occur if FR24feed uploader starts, but the connection to USB or data source is not possible and retrying while you cannot see it
    Causes as above but not seen
    - '--interactive' option sent to Dump1090 (will output to screen not capture data)
    - Blacklisted USB drivers
    - Locked USB port/device
    - Wrong data format
    - software stealing data before FR24feed
    - software not outputting data on specified data port (or in correct format)
    - Bad signal or data being ignored by server
    - Populated COM/DEV/PATH overriding auto-detect

    As with most issues - Use above fault finding to stop, and manually start to observe FR24feed startup messages or errors

    Diagnosing port issues using telnet
    If you are experiencing port connection errors one method to ensure data is working is using the telnet utility

    telnet <host> <port>

    Where <host> can be:

    and port (divided by a space, no other character like
    - as listed in port table for common ports

    A WORKING open port, will result in a black screen with cursor flashing. A blocked port will result in a failure to connect
    Last edited by Oblivian; 2017-04-02 at 10:53.
    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

  3. #3
    Super Moderator
    Join Date
    May 2011
    T-NZCH1, PP:PH New Zealand
    Web Configuration Explained:

    DVBT Stick (default)

    DVB TV Dongle connected directly by USB to host device
    - Launches Dump1090-MR and contacts hardware directly
    - Works only if other DVB/1090 programs not already running and using data from stick
    - host/ip settings ignored

    ModeS Beast (USB/Serial)
    ModeS Beast/Transponder mouse cabled with USB or serial
    - Com port must be specified in Host/IP field
    - Baudrate must be set
    ModeS Beast (TCP)
    ModeS Beast format using ethernet out
    - Host/IP must be specified in Host/IP field

    SBS1/1e (USB)
    SBS1 cabled directly to host
    - configure Com/Dev setting

    SBS1/1e (TCP)
    - Configure Host/IP

    SBS3 (USB)
    SBS3 (TCP)

    *During signup new option "SBSx via Basestation (localhost:30006)"
    - Exact details of function TBA however may allow reading when data relay enabled in basestation suite

    microADSB (USB)
    - Configure Com/Dev path

    AVR (USB/Serial)
    Other AVR capable receivers connected via cable
    - Specify com port details

    AVR (TCP)
    AVR data from pre-configured Rpi running Dump1090
    Data from existing Dump1090/RTL1090 or other such software with AVR server enabled
    - Specify Host/IP details

    Example AVR data format:
    Process arguments
    For devices that use Dump1090 (DVBT/AVR USB) Process arguments field can be used

    RAW data Yes/No *note
    Open server port 30034
    - For Beast and other hardware
    Open server port 30002
    - For DVBT*

    SBS Feed Yes/No
    When Kinetic receiver specified data for basestation output on 20072
    - Configure Basestation software for Ethernet receiver. Specify IP of device FR24feed running and port 20072
    - Voice/ATC functions cannot be used in conjunction with this method

    Decoded Data Yes/No: *note
    Open server port 30003
    - Basestation format text for other capture software
    This is for diagnostic purpose
    - May not auto delete and can fill Rpi cards

    Window Mode
    For windows only
    - Open app in task bar

    Enable MLAT data out to FR24
    - DVBT device by USB or Dump1090 AVR only
    - Enables (or requires) --MLAT tag in Dump1090

    Last edited by Oblivian; 2017-01-23 at 00:56.
    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

  4. #4
    Super Moderator
    Join Date
    May 2011
    T-NZCH1, PP:PH New Zealand
    Linux/Pi specific Information:

    Dump1090 Graphical Interface:
    When --net option is added, and you then visit http://localhost:8080 (or host IP) a map will be provided by Dump1090
    A further port change option can be specified --net-http-port xxxx
    See Dump1090 documentation for further assistance

    Dump1090 Dev Install
    (advanced users recommended only)
    See thread for manual install of Dev version of Dump1090

    Common Linux Commands:
    Linux need not be scary for first time users. Although there is no graphical interface without starting one, the same commands are needed for FR24feed on GUI versions.

    Install FR24feed via script:
    sudo bash -c "$(wget -O -" -

    Run Signup to reconfigure if web not accessible
    sudo fr24feed --signup
    (Enter the identical details as first signup)

    Start feed software with full screen output to diagnose possible errors
    sudo fr24feed start
    (ctrl C to terminate)

    Start feed software as service in background (starts on reboot)
    sudo service fr24feed start

    Stop fr24feed
    sudo service fr24feed stop

    Check fr24feed status
    sudo service fr24feed status
    - Jessie Patch here

    Update fr24feed
    sudo apt-get update - refresh available app update list
    sudo apt-get install --only-upgrade fr24feed - manually check for update
    - Will search for a new version and advise if 0 bytes were to be installed (no change) or if a new update was to be.

    Check for crashed/running instances causing port or start issues:
    - Following command will report a PID for each process
    pgrep -l fr24feed - list running FR24 processes
    pgrep -l dump1090 - list dump1090 instances

    sudo kill -9 <pid> - replace <pid> with corresponding number from above to kill process

    Dump0190-Mutability checks:
    sudo service dump1090-mutability status
    sudo service dump1090-mutability restart
    sudo service dump1090-mutability stop

    Status Variables

    mlat-uplink-stats = 0
    - Nothing uploaded, could be because not enough of other MLAT-receivers in the area.

    Lists the last known problem - may not indicate current fault
    - "no-config" comes from the decoder starting too soon to receive from server
    - both uploaded/not uploaded
    Last edited by Oblivian; 2016-08-21 at 08:53.
    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

  5. #5
    Super Moderator
    Join Date
    May 2011
    T-NZCH1, PP:PH New Zealand
    Below is an example of the signup wizard on Rpi:

    RPi Signup Wizard (1.0.16-x)

    Email Address
    Existing Key if known (blank = request new)
    * Key Recovery

    Antenna Details:
    Latitude 00.0000
    Longitude 000.0000
    Altitude (ft)

    Step 1.3 - Would you like to participate in MLAT calculations? (yes/no)$

    - Only valid for DVBT receiver type

    ** Checks for running software **

    If Dump1090 already present:

    We have detected that you already have a dump1090 instance running. We can therefore automatically configure the FR24 feeder to use existing receiver configuration, or you can manually configure all the parameters.

    Would you like to use autoconfig (*yes*/no)$:

    If PiAware already present:

    We have detected that you already have a PiAware application instaled. We can therefore try to automatically configure the FR24 feeder to use existing receiver configuration, or you can manually configure all the parameters.

    Would you like to use autoconfig (*yes*/no)$:

    Autoconfig not available/chosen:

    Step 4.1 - Receiver selection (in order to run MLAT please use DVB-T stick with dump1090 utility bundled with fr24feed):

    1 - DVBT Stick (USB)
    2 - SBS1/SBS1er (USB/Network)
    3 - SBS3 (USB/Network)
    4 - ModeS Beast (USB/Network)
    5 - AVR Compatible (DVBT over network, etc)
    6 - microADSB (USB/Network)
    7 - SBSx via Basestation (localhost:30006)

    Enter your receiver type (1-7)$:

    DVBT Chosen:

    Step 4.2 - Please select connection type:

    1 - Network connection
    2 - USB directly to this computer

    Step 5.1 - Would you like to enable RAW data feed on port 30334 (yes/no)$:
    Step 5.2 - Would you like to enable Basestation data feed on port 30003 (yes/no)

    - Enables local server. If running Dump1090 or other software with these ports open select NO
    Last edited by Oblivian; 2016-02-09 at 01:48.
    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

  6. #6
    Super Moderator
    Join Date
    May 2011
    T-NZCH1, PP:PH New Zealand
    Blah Blah Blah Blah
    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

  7. #7
    Super Moderator
    Join Date
    May 2011
    T-NZCH1, PP:PH New Zealand
    Possible Configuration Setups:

    (Work In progress - may be incorrect for some hardware unavailable for tests)

    SBS Family:
    May '16 - Possible issue with 18-5 release and not reading SBS data as expected below. Older releases appear OK

    When NVM settings of SBS3 set as standalone opens ports:
    10001 - primary encrypted data
    30005 - audio stream
    30006 - RAW Binary relay

    When Basestation running:
    30005 - audio stream
    30006 - RAW Binary relay
    30003 - basestation format


    1. FR24feed primary connection
    Configure FR24feed to connect to device via USB or LAN (source localhost:10001)
    Enable SBS out option
    Close FR24feed
    Configure basestation to FR24feed as network source
    (settings - hardware settings - network)
    Close Basestation
    Open FR24feed (ensure connecting to SBS3)
    Open Basestation (ensure connecting to FR24feed relay on 20072)

    Other apps should have access to 20072 + 30006 (when BS open)

    2. Basestation Primary Connection
    Configure FR24feed as SBS3 LAN
    Open basestation as normal
    Open FR24feed

    3. SBS3 Standalone mode
    Using basestation configure non-Volatile settings to 'standalone' mode - check default port 10001

    Configure Basestation source to network
    <SBS3 IP>:30006

    Close Basestation

    Configure FR24feed to SBS3 LAN
    Set port details as
    <SBS3 ip>:10001 (_test 2nd connection to 30006_)

    Start FR24feed
    Ensure working
    Open Basestation and ensure connects to SBS3 at same time

    First Option
    Requires Basestation to be open and running before FR24feed launched as below:

    Configure FR24feed for "SBSx via Basestation (localhost:30006)" or via LAN
    Disable SBS relay
    localhost:30006 (or IP of pc running basestation)
    Close FR24feed

    Open Basestation software
    Launch FR24feed

    2nd Option
    Configure FR24feed for USB
    Enable SBS relay
    Close FR24feed

    Configure Basestation for network

    Run FR24feed - check connect via USB
    Open basestation - check connect + display
    Last edited by Oblivian; 2016-05-14 at 10:06.
    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

  8. #8
    Super Moderator
    Join Date
    May 2011
    T-NZCH1, PP:PH New Zealand
    Beast/Transponder Mouse:

    Check any additional software has server and relay options disabled/off and closed

    Configure FR24feed with com port
    Enable BS and RAW options

    Configure downstream apps separately

    hostip:30334 RAW/AVR (multi connect)
    hostip:30003 Basestation format (multi connect)

    DVBT (Windows)
    Select DVBT stick
    Enable BS + RAW
    Connect apps:
    IP:30002 AVR format
    IP:30003 BS format
    Last edited by Oblivian; 2016-02-09 at 01:40.
    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

  9. #9
    Super Moderator
    Join Date
    May 2011
    T-NZCH1, PP:PH New Zealand
    Viewing local traffic from your receiver

    Dump1090 can display local traffic (see first post)

    ADSBScope & VRS example

    VirtualRadarServer or VRS as it is commonly seen described here is a graphical interface with the ability to show locally sourced aircraft position data on a web-page for you or the internet for friends etc.

    It has the ability to log these contacts in a database format (additional plugin required) and show icons and flags if added from basestation software suite or other such sources

    !! It is not designed for those of you without a receiver of some type, or access to data from one. !!

    Paradiselost has in the past made an example page with graphics on setting up VRS and ADSBScope downstream using the RAW output. The same goes for other software, such as tailing off FR24feed output ports (see common ports)


    When you are actively feeding and have a premium account, radar view can be used to attached to your local traffic (fr24feed) and display in a basic format also

    Log in to premium
    Click the "logged in" icon and select radar view
    Add checkmark to Show local (and adjust IP accordingly if Pi/external PC)

    This method is not advised as data quality may not be optimized for FR24 use - Dump1090 has similar web server display capability

    If you run RTL1090 this will already have exclusive control of the USB port
    - FR24feed will also want access if you choose 'DVBT' in configuration
    - RTL1090 will open port 31001, 31004 OUT, 31002 IN when launched.

    Example Configuration:
    Receiver: AVR-TCP
    Source: localhost:31001
    BS & RAW: OFF

    If the format is not recognised (Beast Binary) or other software requires strict AVR - you can over-ride with RTL1090.exe /AVR

    Other applications can connect to RAW/AVR on 31001. Or Basestation format on 31004

    9-2-16 Added RTL1090 info
    14-3-16 added more regarding VRS
    Last edited by Oblivian; 2016-04-21 at 21:17.
    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

  10. #10
    Super Moderator
    Join Date
    May 2011
    T-NZCH1, PP:PH New Zealand

    Generic flow of data

    Optimised for FR24feed use

    'DVBT' (no advanced features)
    DVBT -> USB -> FR24feed -> 30002 (if RAW out enabled)

    'AVR-TCP' (& --NET)
    DVBT -> Dump1090 -> localhost:30002 -> FR24feed (30002 disable)
    DVBT -> Dump1090 -> localhost:30002 -> Other Software

    Linux and non-bundled Dump1090
    If installing Dump1090 or compiling outside of FR24feed bundle, as above posts indicate you must configure FR24feed to connect to Dump1090 via AVR-TCP on 30002
    Attempting to do so on pre-compiled FR24feed or PiAware image without linux knowledge is NOT advised

    Suggested method in basic steps
    Install Dump1090 of choice
    - Configure with advanced options of choosing
    - confirm working using web view
    Install FR24/Piaware package - wizard will detect (if running correctly!) and assist
    - Do NOT select RAW out post install

    Other edits:
    'How it works' section
    More self diagnosis instructions
    - help us help you
    Last edited by Oblivian; 2016-08-21 at 09:36.
    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts