Page 6 of 10 FirstFirst ... 45678 ... LastLast
Results 51 to 60 of 91

Thread: Help Setting Up Flightradar24 Software

  1. #51
    Captain abcd567's Avatar
    Join Date
    Sep 2013
    Location
    Toronto CYYZ
    Posts
    2,852
    flyingLunchbox:

    To reconfigure only
    Code:
    fr24feed --reconfigure
    To signup and reconfigure
    Code:
    fr24feed --signup
    Last edited by abcd567; 2019-07-17 at 22:24.

  2. #52
    Passenger
    Join Date
    May 2019
    Location
    Germanx-Berlin
    Posts
    18
    Hello everybody,

    I've tried so hard to set up the FR24 software for feeding, but I can not get it to work. Can someone help me with the installation of the FR24 software on my Rasberry Pi 2? The software I have already copied to an SD card and the software also starts. The DVBT stick is also recognized. I do not know where to enter my access data?

    Many Thanks
    Nils

  3. #53
    Captain abcd567's Avatar
    Join Date
    Sep 2013
    Location
    Toronto CYYZ
    Posts
    2,852
    wildthing01:

    Which OS you have installed?

    PI24 image downloaded from https://www.flightradar24.com/build-your-own

    OR

    Raspbian image downloaded from https://www.raspberrypi.org/downloads/raspbian/

  4. #54
    Passenger
    Join Date
    May 2019
    Location
    Germanx-Berlin
    Posts
    18
    Hello everybody,

    many thanks for the help. I downloaded the software from Fligthradar24. The feeding software seems to work, but the software does not feed the data into the internet
    My question: What am I doing wrong? Are the parameters / entries not entered correctly? (see attached photo)
    What am I doing wrong. Can someone help me get the feeding software to work?

    Best regards
    Nils20190902_124637.jpg

  5. #55
    Super Moderator
    Join Date
    May 2011
    Location
    T-NZCH1, PP:PH New Zealand
    Posts
    5,049
    Quote Originally Posted by wildthing01 View Post
    Hello everybody,

    many thanks for the help. I downloaded the software from Fligthradar24. The feeding software seems to work, but the software does not feed the data into the internet
    My question: What am I doing wrong? Are the parameters / entries not entered correctly? (see attached photo)
    What am I doing wrong. Can someone help me get the feeding software to work?

    Best regards
    Nils20190902_124637.jpg
    Does not appear so

    sudo fr24feed --signup

    Re-enter same details as before.
    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

  6. #56
    Captain
    Join Date
    Apr 2018
    Posts
    864
    After running the signup, you'll need to restart fr24:

    sudo systemctl restart fr24feed

    I suspect you'll have to look up how to use putty/ssh, it is described here:
    https://forum.flightradar24.com/thre...l=1#post121506
    Last edited by wiedehopf; 2019-09-02 at 11:35.

  7. #57
    Passenger
    Join Date
    May 2019
    Location
    Germanx-Berlin
    Posts
    18
    The system tells me that my email address is wrong. Earlier on the Windows feeding software I logged in with the same email address.
    What am I doing wrong?
    I'm sorry for the questions to the forum.
    20190902_142915.jpg

  8. #58
    Captain
    Join Date
    Apr 2018
    Posts
    864
    Leave the prompt for the sharing key empty.

    You will then get a new sharing key.
    Old sharing keys often cause problems.

  9. #59
    Passenger
    Join Date
    May 2019
    Location
    Germanx-Berlin
    Posts
    18
    Hello,

    The feeding software now seems to be fully configured
    Except for a few minor misunderstandings.
    How do I get the software to feed.
    with the command:
    sudo service fr24feed start
    Do not start feeding?
    Can someone help me please? or is it enough if I restart the Raspberry?

    Many thanks in advance for your reply

  10. #60
    Captain
    Join Date
    Apr 2018
    Posts
    864
    Don't type start, type restart!

    sudo systemctl restart fr24feed

    Anyway you can also reboot the RPi.

    Also consider upgrading dump1090, fr24 is by default using a very old version.
    https://github.com/wiedehopf/adsb-sc...for-dump1090fa

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •