Page 1 of 7 123 ... LastLast
Results 1 to 10 of 69

Thread: Raspberry Pi:How To Install Raspian OS + Dump1090 + FR24 Data Feeder

  1. #1
    Captain abcd567's Avatar
    Join Date
    Sep 2013
    Location
    Toronto CYYZ
    Posts
    2,309

    Raspberry Pi:How To Install Raspian OS + Dump1090 + FR24 Data Feeder

    LAST UPDATED: February 23, 2018


    Options 1 & 2 are in this post.
    Options 3 & 4 are in post #3


    OPTION - 1:
    Raspbian OS with integral dump1090-mutability v1.14 + FR24 data feeder
    Easiest, Plug-And-Play

    (1) Download Pi24 image and burn on your microSD card.
    Download page: https://www.flightradar24.com/build-your-own


    (2) After burning the Pi24 image to microSD card, insert the microSD card into Pi and power-up

    If you are using fr24feed for the first time and don't have fr24 sharing key, go to this page and follow instructions:
    https://www.flightradar24.com/activate-raspberry-pi


    (3) If you want to activate and configure manually, give following command.
    Code:
    sudo fr24feed --signup
    You will be asked to enter your email address, fr24 sharing key, antenna position and other details.
    If you dont already have fr24 sharing key, a new key will be saved in file /etc/fr24feed.ini automatically.
    You will also get it by email on the address you have entered.

    Code:
    Step 1.1 - Enter your email address (username@domain.tld)
    $: xxx@yyyyy.com
    
    Step 1.2 - If you used to feed FR24 with ADS-B data before enter your sharing key.
    If you don't remember your sharing key, pelase use the retrival form:
    http://feed.flightradar24.com/forgotten_key.php
    
    Otherwise leave this field empty and continue.
    $: xxxxxxxxxxxxxxxx
    (leave blank if you dont have a key)
    
    Step 1.3 - Would you like to participate in MLAT calculations? (yes/no)$: yes
    
    IMPORTANT: For MLAT calculations the antenna's location should be entered very precise!
    
    Step 3.A - Enter antenna's latitude (DD.DDDD)
    $: xx.xxxx (use your actual latitude in place of xx.xxxx)
    
    Step 3.B - Enter antenna's longitude (DDD.DDDD)
    $: yy.yyyy (use your actual longitude in place of yy.yyyy)
    
    Step 3.C - Enter antenna's altitude above the sea level (in feet)
    $: zzz (use your actual height in place of zzz)
    
    Using latitude: xx.xxxx, longitude: yy.yyyy, altitude: zzzft above sea level
    
    Validating email/location information...OK
    
    The closest airport found is ICAO:CYYZ IATA:YYZ near Toronto.
    
    Latitude: 43.677219
    Longitude: -79.630501
    Country: Canada
    
    Flightradar24 may, if needed, use your email address to contact you regarding your data feed.
    
    Would you like to continue using these settings?
    
    Enter your choice (yes/no)$: yes
    (4) After signup, configuration will start. Enter values show in red below:
    Code:
    Step 4.1 - Receiver selection (in order to run MLAT please use DVB-T stick with dump1090 utility bundled with fr24feed):
    
     1 - DVBT Stick (USB)
     -----------------------------------------------------
     2 - SBS1/SBS1er (USB/Network)
     3 - SBS3 (USB/Network)
     4 - ModeS Beast (USB/Network)
     5 - AVR Compatible (DVBT over network, etc)
     6 - microADSB (USB/Network)
     7 - SBSx via Basestation (localhost:30006)
    
    
    Enter your receiver type (1-7)$: 1
    Checking for dump1090...NOT FOUND
    
    Step 4.3 - Enter your additional dump1090 arguments or leave empty
    $:
    
    Step 5.1 - Would you like to enable RAW data feed on port 30002 (yes/no)$: no
    
    Step 5.2 - Would you like to enable Basestation data feed on port 30003 (yes/no)$: no
    
    Step 6A - Please select desired logfile mode:
     0 -  Disabled
     1 -  48 hour, 24h rotation
     2 -  72 hour, 24h rotation
    Select logfile mode (0-2)$: 1
    
    Step 6B - Please enter desired logfile path (/var/log/fr24feed):
    $:
    
    Submitting form data...OK
    
    Congratulations! You are now registered and ready to share ADS-B data with Flightradar24.
    + Your sharing key (xxxxxxxxxxxxxxxx) has been configured and emailed to you for backup purposes.
    + Your radar id is T-CYYZxx, please include it in all email communication with us.
    + Please make sure to start sharing data within the next 3 days as otherwise your ID/KEY will be deleted.
    
    Thank you for supporting Flightradar24! We hope that you will enjoy our Premium services that will be available to you when you become an active feeder.
    
    To start sending data now please execute:
    sudo systemctl start fr24feed
    
    Saving settings to /etc/fr24feed.ini...OK

    (5) Restart fr24feed
    Code:
    sudo systemctl restart fr24feed


    To view STATUS: Type following address in your browser, and status page will appear:
    ip-of-pi:8754
    (ip-of-pi will be something like 192.168.0.21)

    To view or change SETTINGS: Type following address in your browser, and settings page will appear:
    ip-of-pi:8754/settings.html


    SETTINGS FOR PI24 image
    PI24 - Settings.png PI24 - Status.png PI24 - Map.png






    OPTION - 2:
    Raspbian OS.
    Package (FR24 feeder + dump1090-mutability v1.14) installed by user.

    Flexible, can smoothly run other apps if required.

    (1) Download latest Raspbian image on your computer, and write the downloaded image to your microSD card. Download and installation instructions are here: https://www.raspberrypi.org/downloads/

    (2) To install FR24 data feeder + dump1090-mutability v 1.14, SSH into your Raspberry Pi and execute this command:
    Code:
    sudo bash -c "$(wget -O - http://repo.feed.flightradar24.com/install_fr24_rpi.sh)"
    (3) You will be asked to enter your email address, fr24 sharing key, antenna position and other details.
    If you dont already have fr24 sharing key, a new key will be saved in file /etc/fr24feed.ini automatically. You will also get it by email on the address you have entered.

    Code:
    Step 1.1 - Enter your email address (username@domain.tld)
    $: xxx@yyyyy.com
    
    Step 1.2 - If you used to feed FR24 with ADS-B data before enter your sharing key.
    If you don't remember your sharing key, pelase use the retrival form:
    http://feed.flightradar24.com/forgotten_key.php
    
    Otherwise leave this field empty and continue.
    $: xxxxxxxxxxxxxxxx
    (leave blank if you dont have a key)
    
    Step 1.3 - Would you like to participate in MLAT calculations? (yes/no)$: yes
    
    IMPORTANT: For MLAT calculations the antenna's location should be entered very precise!
    
    Step 3.A - Enter antenna's latitude (DD.DDDD)
    $: xx.xxxx (use your actual latitude in place of xx.xxxx)
    
    Step 3.B - Enter antenna's longitude (DDD.DDDD)
    $: yy.yyyy (use your actual longitude in place of yy.yyyy)
    
    Step 3.C - Enter antenna's altitude above the sea level (in feet)
    $: zzz (use your actual height in place of zzz)
    
    Using latitude: xx.xxxx, longitude: yy.yyyy, altitude: zzzft above sea level
    
    Validating email/location information...OK
    
    The closest airport found is ICAO:CYYZ IATA:YYZ near Toronto.
    
    Latitude: 43.677219
    Longitude: -79.630501
    Country: Canada
    
    Flightradar24 may, if needed, use your email address to contact you regarding your data feed.
    
    Would you like to continue using these settings?
    
    Enter your choice (yes/no)$: yes
    (4) After signup, configuration will start. Enter values show in red below:
    Code:
    Step 4.1 - Receiver selection (in order to run MLAT please use DVB-T stick with dump1090 utility bundled with fr24feed):
    
     1 - DVBT Stick (USB)
     -----------------------------------------------------
     2 - SBS1/SBS1er (USB/Network)
     3 - SBS3 (USB/Network)
     4 - ModeS Beast (USB/Network)
     5 - AVR Compatible (DVBT over network, etc)
     6 - microADSB (USB/Network)
     7 - SBSx via Basestation (localhost:30006)
    
    
    Enter your receiver type (1-7)$: 1
    Checking for dump1090...NOT FOUND
    
    Step 4.3 - Enter your additional dump1090 arguments or leave empty
    $:
    
    Step 5.1 - Would you like to enable RAW data feed on port 30002 (yes/no)$: no
    
    Step 5.2 - Would you like to enable Basestation data feed on port 30003 (yes/no)$: no
    
    Step 6A - Please select desired logfile mode:
     0 -  Disabled
     1 -  48 hour, 24h rotation
     2 -  72 hour, 24h rotation
    Select logfile mode (0-2)$: 1
    
    Step 6B - Please enter desired logfile path (/var/log/fr24feed):
    $:
    
    Submitting form data...OK
    
    Congratulations! You are now registered and ready to share ADS-B data with Flightradar24.
    + Your sharing key (xxxxxxxxxxxxxxxx) has been configured and emailed to you for backup purposes.
    + Your radar id is T-CYYZxx, please include it in all email communication with us.
    + Please make sure to start sharing data within the next 3 days as otherwise your ID/KEY will be deleted.
    
    Thank you for supporting Flightradar24! We hope that you will enjoy our Premium services that will be available to you when you become an active feeder.
    
    To start sending data now please execute:
    sudo systemctl start fr24feed
    
    Saving settings to /etc/fr24feed.ini...OK

    (5) Restart fr24feed
    Code:
    sudo systemctl restart fr24feed
    To view STATUS: Type following address in your browser, and status page will appear:
    ip-of-pi:8754
    (ip-of-pi will be something like 192.168.0.21)

    To view or change SETTINGS: Type following address in your browser, and settings page will appear:
    ip-of-pi:8754/settings.html


    SETTINGS FOR Raspbian image + dump1090-mutability v 1.14
    PI24 - Settings.png PI24 - Status.png PI24 - Map.png


    Please see this page for latest information: https://www.flightradar24.com/raspberry-pi
    Last edited by abcd567; 2018-02-23 at 19:30.

  2. #2
    Passenger
    Join Date
    Dec 2012
    Posts
    7
    My setup looks like the screenshots and works well.

    I run PP, SBS Plotter and the Google map

    Setup1.jpgRPi_Service.jpg

  3. #3
    Captain abcd567's Avatar
    Join Date
    Sep 2013
    Location
    Toronto CYYZ
    Posts
    2,309
    OPTION 3:
    [b]Raspbian OS
    The Decoder of user's choice installed by user.
    The FR24 datafeeder installed by user (Do NOT use DVBT mode. Must be configured in AVR(TCP) or Beast (TCP) mode).

    MOST FLEXIBLE. Suitable if other Apps or data feeders are also run on the Pi.

    (1) Download on your computer Raspbian image from Raspberry Pi foundation site, and write the downloaded image to your microSD card.

    Download and installation instructions are here: http://www.raspberrypi.org/downloads

    (2) This image does not have a decoder. You have to first install a decoder of your choice such as dump1090-mutability v 1.15~dev, or dump1090-fa, ModeSDeco2 etc.


    (3) After installation of a decoder, install fr24feed using bash script
    Code:
    sudo bash -c "$(wget -O - http://repo.feed.flightradar24.com/install_fr24_rpi.sh)"
    During installation, you will be asked to enter your email address, fr24 sharing key, antenna position and other details.
    If you dont already have fr24 sharing key, a new key will be saved in file /etc/fr24feed.ini automatically.
    You will also get it by email on the address you have entered.

    Code:
    Step 1.1 - Enter your email address (username@domain.tld)
    $: xxx@yyyyy.com
    
    Step 1.2 - If you used to feed FR24 with ADS-B data before enter your sharing key.
    If you don't remember your sharing key, pelase use the retrival form:
    http://feed.flightradar24.com/forgotten_key.php
    
    Otherwise leave this field empty and continue.
    $: xxxxxxxxxxxxxxxx
    (leave blank if you dont have a key)
    
    Step 1.3 - Would you like to participate in MLAT calculations? (yes/no)$: yes
    
    IMPORTANT: For MLAT calculations the antenna's location should be entered very precise!
    
    Step 3.A - Enter antenna's latitude (DD.DDDD)
    $: xx.xxxx (use your actual latitude in place of xx.xxxx)
    
    Step 3.B - Enter antenna's longitude (DDD.DDDD)
    $: yy.yyyy (use your actual longitude in place of yy.yyyy)
    
    Step 3.C - Enter antenna's altitude above the sea level (in feet)
    $: zzz (use your actual height in place of zzz)
    
    Using latitude: xx.xxxx, longitude: yy.yyyy, altitude: zzzft above sea level
    
    Validating email/location information...OK
    
    The closest airport found is ICAO:CYYZ IATA:YYZ near Toronto.
    
    Latitude: 43.677219
    Longitude: -79.630501
    Country: Canada
    
    Flightradar24 may, if needed, use your email address to contact you regarding your data feed.
    
    Would you like to continue using these settings?
    
    Enter your choice (yes/no)$: yes

    (4) After signup, configuration will start. Enter values show in red below:

    Code:
    1 - DVBT Stick (USB)
     -----------------------------------------------------
     2 - SBS1/SBS1er (USB/Network)
     3 - SBS3 (USB/Network)
     4 - ModeS Beast (USB/Network)
     5 - AVR Compatible (DVBT over network, etc)
     6 - microADSB (USB/Network)
     7 - SBSx via Basestation (localhost:30006)
    
    
    Enter your receiver type (1-7)$: 4
    
    Step 4.2 - Please select connection type:
    
     1 - Network connection
     2 - USB directly to this computer
    
    Enter your connection type (1-2)$: 1
    
    Step 4.3A - Please enter your receiver's IP address/hostname
    $: 127.0.0.1
    
    Step 4.3B - Please enter your receiver's data port number
    $: 30005
    (5) Restart fr24feed
    Code:
    sudo systemctl restart fr24feed
    To view STATUS: Type following address in your browser, and status page will appear:
    ip-of-pi:8754
    (ip-of-pi will be something like 192.168.0.21)

    To view or change SETTINGS: Type following address in your browser, and settings page will appear:
    ip-of-pi:8754/settings.html
    (ip-of-pi will be something like 192.168.0.21)



    SETTINGS FOR RASPBIAN images
    FR24 on Raspbian or Piaware img - Status.png FR24 on Raspbian or Piaware img - Settings.png




    OPTION 4:
    Raspbian OS with integral dump1090-fa and Flightaware datafeeder.
    The FR24 datafeeder installed by user (Do NOT use DVBT mode. Must be configured in AVR(TCP) or Beast (TCP) mode).

    (1) Download PiAware image from FlightAware on your computer, and write the downloaded image to your microSD card.

    This image has dump1090-fa + Flightaware data feeder pre-installed.

    Download and installation instructions are here: http://flightaware.com/adsb/piaware/build
    This image contains operating system Raspbian, dump1090 and Flightaware data feeder.

    (2) SSH into your Raspberry Pi and execute this command to install FR24 data feeder:
    Code:
    sudo bash -c "$(wget -O - http://repo.feed.flightradar24.com/install_fr24_rpi.sh)"
    (3) You will be asked to enter your email address, fr24 sharing key, antenna position and other details.
    If you dont already have fr24 sharing key, a new key will be saved in file /etc/fr24feed.ini automatically.
    You will also get it by email on the address you have entered.

    Code:
    Step 1.1 - Enter your email address (username@domain.tld)
    $: xxx@yyyyy.com
    
    Step 1.2 - If you used to feed FR24 with ADS-B data before enter your sharing key.
    If you don't remember your sharing key, pelase use the retrival form:
    http://feed.flightradar24.com/forgotten_key.php
    
    Otherwise leave this field empty and continue.
    $: xxxxxxxxxxxxxxxx
    (leave blank if you dont have a key)
    
    Step 1.3 - Would you like to participate in MLAT calculations? (yes/no)$: yes
    
    IMPORTANT: For MLAT calculations the antenna's location should be entered very precise!
    
    Step 3.A - Enter antenna's latitude (DD.DDDD)
    $: xx.xxxx (use your actual latitude in place of xx.xxxx)
    
    Step 3.B - Enter antenna's longitude (DDD.DDDD)
    $: yy.yyyy (use your actual longitude in place of yy.yyyy)
    
    Step 3.C - Enter antenna's altitude above the sea level (in feet)
    $: zzz (use your actual height in place of zzz)
    
    Using latitude: xx.xxxx, longitude: yy.yyyy, altitude: zzzft above sea level
    
    Validating email/location information...OK
    
    The closest airport found is ICAO:CYYZ IATA:YYZ near Toronto.
    
    Latitude: 43.677219
    Longitude: -79.630501
    Country: Canada
    
    Flightradar24 may, if needed, use your email address to contact you regarding your data feed.
    
    Would you like to continue using these settings?
    
    Enter your choice (yes/no)$: yes

    (4) After signup, configuration will start. Enter values show in red below:

    Code:
    1 - DVBT Stick (USB)
     -----------------------------------------------------
     2 - SBS1/SBS1er (USB/Network)
     3 - SBS3 (USB/Network)
     4 - ModeS Beast (USB/Network)
     5 - AVR Compatible (DVBT over network, etc)
     6 - microADSB (USB/Network)
     7 - SBSx via Basestation (localhost:30006)
    
    
    Enter your receiver type (1-7)$: 4
    
    Step 4.2 - Please select connection type:
    
     1 - Network connection
     2 - USB directly to this computer
    
    Enter your connection type (1-2)$: 1
    
    Step 4.3A - Please enter your receiver's IP address/hostname
    $: 127.0.0.1
    
    Step 4.3B - Please enter your receiver's data port number
    $: 30005
    (5) Restart fr24feed
    Code:
    sudo systemctl restart fr24feed
    To view STATUS: Type following address in your browser, and status page will appear:
    ip-of-pi:8754
    (ip-of-pi will be something like 192.168.0.21)

    To view or change SETTINGS: Type following address in your browser, and settings page will appear:
    ip-of-pi:8754/settings.html
    (ip-of-pi will be something like 192.168.0.21)



    SETTINGS FOR RASPBIAN & PIAWARE images
    FR24 on Raspbian or Piaware img - Status.png FR24 on Raspbian or Piaware img - Settings.png


    Please see this page for latest information: https://www.flightradar24.com/raspberry-pi

    Download Guide (pdf) from here: http://feed.flightradar24.com/fr24feed-manual.pdf

    GOOD LUCK!!!!
    Last edited by abcd567; 2018-02-23 at 19:27.

  4. #4
    Passenger
    Join Date
    Feb 2013
    Posts
    9
    abcd567, I just want to thank you so much for the info to set up FR24 Feed with piaware. I've been going crazy trying to find a way to get that to work.
    Your info made it so easy. I followed your instructions and it worked with no problems at all. Thanks again.

  5. #5
    Passenger
    Join Date
    Feb 2013
    Posts
    9
    Ok, I'm now uploading data to FR24 thru my RasPi and I see stats for aircraft and positions but "Current upload rate" shows "0 KB/s".
    Is this normal?

  6. #6
    Passenger papasven's Avatar
    Join Date
    Jan 2014
    Location
    near Berlin
    Posts
    14
    Quote Originally Posted by djmarko413 View Post
    Ok, I'm now uploading data to FR24 thru my RasPi and I see stats for aircraft and positions but "Current upload rate" shows "0 KB/s".
    Is this normal?
    A while ago I saw values there i believe, otherwise all ok.

    Unbenannt.png
    | T-EDDB8 |T-EDDB28 | Virtual Radar | Dump1090 | ModesMixer2 |

  7. #7
    Passenger
    Join Date
    Feb 2013
    Posts
    9
    Quote Originally Posted by papasven View Post
    A while ago I saw values there i believe, otherwise all ok.

    Unbenannt.png
    Ok, thanks for that info.

  8. #8
    Flight attendant
    Join Date
    Mar 2015
    Location
    Nancy, France
    Posts
    65
    Quote Originally Posted by abcd567 View Post
    What you need is 3 components as follows:
    1- An operating system like Raspbian.
    2- A decoder software like Dump1090
    3- A Data Feeding software.
    Thank you very much for such a detailed and well explained procedure, I was able to set-up everything very quickly!

  9. #9
    Purser
    Join Date
    Apr 2015
    Location
    Germany
    Posts
    129
    Quote Originally Posted by abcd567 View Post
    What you need is 3 components as follows:
    1- An operating system like Raspbian.
    2- A decoder software like Dump1090
    3- A Data Feeding software.

    OPTION A:
    You can install each component separately in three (3) steps shown below.

    OPTION B:
    An easier option is to install PiAware image from FlightAware. PiAware is a complete package containing all above three components in one image file, but its Data Feeder is for Flight Aware only. To feed FR24, you will have to install FR24 data feeder (step 3 below) after installing PiAware image.

    I have prepared two 8 GB microSD cards, one with option A, and other with option B, and both work ok.


    STEP 1- Install Raspbian Wheezy on microSD Card
    Download Raspbian (Debian Wheezy) on your Desktop/Laptop from Raspberry Pi's Official Website http://www.raspberrypi.org/downloads/. Scroll down the page to find Raspbian Wheezy.

    After download follow instructions on this page http://www.raspberrypi.org/documenta...ages/README.md.

    You will need a TV/monitor, mouse & keyboard for first install. Select GUI option (Graphical User Interface like windows) when configuration starts at the end of install.

    Alternatively, instead of downloading Raspbian Wheezy from above noted page, you may download NOOBS from the same page, and choose option Raspbian during installation of NOOBS. Instruction for Installation of NOOBS are here http://www.raspberrypi.org/help/noobs-setup/



    STEP 2- Install rtl-sdr Drivers and Decoder Dump1090
    This requires using console of Raspbian Wheezy. You can visit these two sites for instructions:
    https://ferrancasanovas.wordpress.co...-installation/

    http://www.satsignal.eu/raspberry-pi/dump1090.html

    I will list the console commands here which I got from these sites:

    2a- Install updates, upgrades and tools
    Code:
    sudo apt-get update
    sudo apt-get upgrade
    sudo apt-get install git-core
    sudo apt-get install git 
    sudo apt-get install cmake
    sudo apt-get install libusb-1.0-0-dev
    sudo apt-get install build-essential
    2b- Install RTL-SDR Drivers
    Code:
    git  clone  git://git.osmocom.org/rtl-sdr.git
    cd  rtl-sdr
    mkdir  build
    cd  build
    cmake  ../ -DINSTALL_UDEV_RULES=ON
    make
    sudo  make  install
    sudo  ldconfig
    2c- Install dump1090 (Please see post # 3 below before proceeding)
    Code:
    cd ~
    sudo  cp  ./rtl-sdr/rtl-sdr.rules  /etc/udev/rules.d/
    sudo  reboot
    cd  ~ 
    git  clone  git://github.com/MalcolmRobb/dump1090.git
    cd  dump1090
    make
    ./dump1090 --interactive --net --net-http-port 8080
    You may get following error message;
    Code:
    Kernel driver is active, or device is claimed by second instance
    In the first case, please either detach or blacklist the kernel
    (dvb_usb_rtl28xxu), or enable automatic detaching at compile tim
    
    usb_claim_interface error -6
    Error opening the RTLSDR device: Device or resource busy
    To solve this problem you have to create a blacklist file as follows:
    Code:
    cd  /etc/modprobe.d
    sudo nano /etc/modprobe.d/rtl-sdr-blacklist.conf
    This will create & open the blacklist file rtl-sdr-blacklist.conf
    type following lines in this file & save the file.
    Code:
    blacklist dvb_usb_rtl28xxu
    blacklist e4000
    blacklist rtl2832
    To enable display of planes on Google Map in a Browser, give following command in console:
    Code:
    cd dump1090
    ./dump1090 --interactive --net --net-http-port 8080


    STEP 3- Installation of FR24 Data feeder :
    (Source: http://forum.flightradar24.com/threa...-BETA-testing-)

    Type following command in your console:
    Code:
    sudo wget http://feed.flightradar24.com/raspberry-pi/fr24feed_1.0.12-3_armhf.deb
    This will download .deb installation file in Downloads folder of your RPi.
    install the data feeding software using following console command:

    Code:
    sudo dpkg -i fr24feed_1.0.12-3_armhf.deb
    If this is the first time you’re going to share data with FR24, use the command below:
    Code:
    sudo fr24feed --signup
    If you have already obtained a a data sharing key from FR24, or are already sharing data with FR24 from another computer and want to now feed from RPi instead, use the same sharing key you already have, and start the configuration process by executing:
    Code:
    sudo fr24feed --reconfigure --fr24key=YOUR SHARING KEY
    Complete the configuration wizard. When asked for additioal arguments for dump1090, enter following:
    Code:
    --net --net-http-port 8080
    Now start sharing your data by typing:
    Code:
    sudo service fr24feed restart
    Now run the command:
    Code:
    service fr24feed status
    You will see following "Fail, Receiver down" (last line)
    Code:
    pi@piaware ~ $ service fr24feed status
    [ ok ] FR24 Feeder/Decoder Process: running.
    [ ok ] FR24 Stats Timestamp: 2015-01-21 17:46:02.
    [ ok ] FR24 Link: connected [UDP].
    [ ok ] FR24 Radar: T-CYYZ9.
    [ ok ] FR24 Tracked AC:.
    [FAIL] Receiver: down ... failed!
    Then follow steps shown in the screenshots below:

    Attachment 5753 . Attachment 5754 . Attachment 5755

    Now again run the command "service fr24feed status",
    Now the message:
    [FAIL] Receiver: down ... failed!
    will be replaced by:
    [ ok ] Receiver: connected (xxx MSGS/0 SYNC).


    During the next system restart FR24 decoder/feeder will start automatically.

    Download Guide (pdf) from here: http://feed.flightradar24.com/fr24feed-manual.pdf

    GOOD LUCK!!!!
    Man you save my life, afthe 1 day tryng make my PI works, i found this topic, really 192.168.0.x:5784/settings.html this make a difference....... this topic must be merged on flightradar24 install notes for RPI, maybe new users need them.
    Really thanks for that.

    Cheers
    Last edited by mrcarlos; 2015-04-19 at 20:09.

  10. #10
    Passenger
    Join Date
    Apr 2015
    Posts
    9
    Thanks for your guide, unfortunately I've hit a problem.
    I keep hitting the problem described in the end of step 2.
    I made the blacklist but still it keeps giving the error, is this normal or should I proceed?


    After redoing steps 2 and 3 I got it working
    Last edited by thebenchmark; 2015-04-26 at 00:33.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •