Hello Mike,Originally Posted by Mike
looks very good for the start.
It can be started on my debian ARM sheevaplug and also my Raspberry PI:
$ ./fr24feed_arm-le_222 --fr24key=YOUR_SHARING_KEY
[i]Downloading configuration...OK
[i]Parsing configuration...ERROR
[failure]: Not found, check your key!
{"result":"failure","info":"Not found, check your key!"}
Please provide me with a SHARED-KEY.
My airport is EDDK (cologne airport CGN).
Thanks
Willi
Great!
Please send an email to info@flight24.com so we get you correctly registered in the system.
Already done.
Hallo Walt,
the author (Roman) told me that the latest version is http://diseqc.org.ua/projects/hard/a...0120427.tar.gz (27.4.2012).
Do you have a newer version or is your version of 2011?
With adsbox I do not get any airplanes at all with microADSB (this worked on windows).
Which serial driver are you using=
cdc_acm does not look correct: "This device cannot do calls on its own. It is not a modem."
[1816305.887752] usb 1-1.2: USB disconnect, address 4
[1816308.431911] usb 1-1.2: new full speed USB device using orion-ehci and address 5
[1816308.544874] usb 1-1.2: New USB device found, idVendor=04d8, idProduct=000a
[1816308.551977] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[1816308.559498] usb 1-1.2: Product: ADSB-PIC V.10 (sprut 2012)
[1816308.565221] usb 1-1.2: Manufacturer: sprut (www.sprut.de)
[1816308.573286] usb 1-1.2: configuration #1 chosen from 1 choice
[1816308.583029] cdc_acm 1-1.2:1.0: This device cannot do calls on its own. It is not a modem.
[1816308.592830] cdc_acm 1-1.2:1.0: ttyACM0: USB ACM device
How do you use micoADSB on linux?
Is there any trick to init microADSB or use a special driver?
Regards
Willi
Hello Willi,
The output is OK. Check that all DIPs of microADSB shall be switched OFF (for Linux).
Is your command like this?
adsbox -s /dev/ttyACM0 -l <your lat> -g <your lon> -r <path to the log file (optional)> -d
I use newer version than is in a site. This version corrects a small trouble with decoding a data of transponders of old USSR-made planes and it same as version from 27.04.2012. If the author lets to me, I can send it to you.
BR,
Walt
Last edited by Walt; 2012-09-22 at 06:49.
Hello Mike,
Can you compile an ARM version with statically linked libraries (with key -static)?
Thanks.
BR,
Walt
Hello Walt,
the V3 version of microADSB does not have any DIP switches. Instead changes are done on a special version of adsbscope on windows.
What are the meanings of these switches?
Could you do me tha favour and tell me what "dmesg" says for your microADSB? Mine shows:
1816308.431911] usb 1-1.2: new full speed USB device using orion-ehci and address 5
[1816308.544874] usb 1-1.2: New USB device found, idVendor=04d8, idProduct=000a
[1816308.551977] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[1816308.559498] usb 1-1.2: Product: ADSB-PIC V.10 (sprut 2012)
[1816308.565221] usb 1-1.2: Manufacturer: sprut (www.sprut.de)
[1816308.573286] usb 1-1.2: configuration #1 chosen from 1 choice
[1816308.583029] cdc_acm 1-1.2:1.0: This device cannot do calls on its own. It is not a modem.
[1816308.592830] cdc_acm 1-1.2:1.0: ttyACM0: USB ACM device
Thanks a lot!
Best regards
Willi
Hello Willi,
This is my output:
usb 1-1: new full speed USB device using at91_ohci and address 2
cdc_acm 1-1:1.0: This device cannot do calls on its own. It is not a modem.
cdc_acm 1-1:1.0: ttyACM0: USB ACM device
BR,
Walt
Last edited by Walt; 2012-09-23 at 04:58.
To initialize microADSB v3 in Linux execute folowing befor starting adsbox:
echo '#43-02' > /dev/ttyACM0
Best regards
Petr K.
Thanks a lot. I should have read your message some hours ago.
In the meantime I had looked into the manual and seen found out that I can send commands to the receiver, like the one mentioned.
There is also "#00" to get the receivers firmware version and others.
Now adsbox works!
