Page 13 of 71 FirstFirst ... 311121314152363 ... LastLast
Results 121 to 130 of 707

Thread: Linux feeder software for Flightradar24 (Old software)

  1. #121
    Passenger
    Join Date
    Jan 2013
    Posts
    17
    Quote Originally Posted by spforums View Post
    gidi...thanks, I had already tried that but no joy.

    jestemradek...thanks, used your code but isn't working yet..checking my setup.
    Couldn't get the script to run however as suggested, but used some of the code after installing 'screen' module...

    Revised code I used in rc.local (I'm using a different port):

    #!/bin/bash
    .
    .
    .
    screen -S dump1090 -d -m /usr/local/bin/dump1090 --net --enable-agc --net-sbs-port 30000
    sleep 30
    screen -S fr24 -d -m /usr/local/bin/fr24feed_arm-le_225s --fr24key=**************** --bs-port=30000
    So, many thanks

    Stu
    Last edited by spforums; 2013-02-11 at 23:41.

  2. #122
    Passenger
    Join Date
    Jan 2013
    Location
    next to Linz airport
    Posts
    43
    any news about a built in decoder for the linux feeder???
    i am still looking for a solution to feed with my raspberrypi and SBS-3, connected via IP, without BS.

  3. #123
    Passenger
    Join Date
    Dec 2012
    Location
    Poland
    Posts
    21
    Just try adsbox. It's make signal BS on tcp/ip port from raw tcp/ip.

    Regards
    Radek
    T-LKPD1
    My native language is polish.

  4. #124
    Passenger
    Join Date
    Jan 2013
    Location
    next to Linz airport
    Posts
    43
    from raw but not from decrypted on port 10001

  5. #125
    Passenger
    Join Date
    Jan 2013
    Posts
    43
    I switched to a new Raspberry Pi, and adsbox is working fine. When connecting the FR24 feeder software I get:

    [i]FR24Feed v225 - built on Oct 8 2012/09:38:58
    [i]Downloading configuration...OK
    [i]Parsing configuration...OK
    [c]Interval: 5s
    [c]Latitude: 51.1500
    [c]Longitude: 3.2330
    [c]GND: YES
    [c]NonADSB: YES
    [i]Source defined as Basestation
    [n]EBOS5@83.XXX.XXX.XX:8099/UDP
    [n]connecting
    [b]connecting to localhost:30003
    [n]connected
    [n]switching to UDP
    [n]working

    And then nothing for 20 seconds, then:

    [n]ping
    [n]ping
    [e]Could not connect to BS
    [i]waiting 5 seconds
    [i]Source defined as Basestation
    [b]connecting to localhost:30003
    [n]ping

    Keeps going like this.
    Last edited by Zorba; 2013-02-16 at 22:20.

  6. #126
    Passenger
    Join Date
    Jan 2013
    Posts
    17
    A couple of suggestions - any chance of the linux feed software output lines to have a date/time stamp prefix? This would be interesting to analyse peak/troughs in traffic. Also show 'Network [0.0MB/0.0MB]' accumulation on a per line basis same as the pc feed software? Thanks.

  7. #127
    Passenger
    Join Date
    Jan 2013
    Posts
    43
    A new version of adsbox should be available soon
    Last edited by Zorba; 2013-02-24 at 12:22.

  8. #128
    Passenger
    Join Date
    Feb 2013
    Location
    on the Coast of the Baltic Sea
    Posts
    3
    Hello,

    I'm new here and have a question about the feedersoftware.
    My Setup is a RTL2832U USB Stick on a Raspberry Pi.
    Decodersoft is dump1090, all it works.
    If I start the feedersoftware all looks fine exept my location (latitude 0.0000 longitude 0.0000).
    Parameter set on start has no effect.
    How can I fix this?

    many thanks.
    socatatb20

  9. #129
    Passenger
    Join Date
    Feb 2013
    Location
    on the Coast of the Baltic Sea
    Posts
    3
    Sorry , fixed!
    I use the static linked version now!

  10. #130
    Passenger
    Join Date
    Feb 2013
    Location
    London, UK
    Posts
    43
    A few points:

    I noticed the dynamically linked version of fr24feed_arm-le_225 did not get my Lat/Long correctly.
    The statically linked version does, and reports it correctly as it starts up, but I think it is getting these values from FR24, not
    from my local environment, so perhaps this does not matter.

    I need
    Code:
    FR24AUTHIP=83.140.247.20
    export  FR24AUTHIP
    before starting the feed with
    Code:
    ./fr24feed_arm-le_225s   --fr24key=MY_SHARING_KEY   >  /dev/null  &
    If you do not redirect the output of fr24feed* to /dev/null and you are using screen
    to detach the feeding process, you will eventually end up with a massive logfile of the output screen is saving for you
    and this may crash your server.

    My setup: An RPi, , running raspian with rtl-sdr and dump1090. The ADS-B receiver is a Realtek Semiconductor
    Corp. RTL2838 DVB-T USB stick with a homebuilt 1090MHz antenna, in, but hopefully soon to be on, the roof.

    dump1090 uses only about 40%cpu to track 40 planes, and displays all the traffic it can see at http://RPi:8080
    (plotted on google maps, sadly, when OpenStreetMap would be a better idea)

    My thanks to all the contributors to this thread, this has been a lot of fun!

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •