Page 2 of 5 FirstFirst 1234 ... LastLast
Results 11 to 20 of 44

Thread: Receiver is online but not sending any data

  1. #11
    Passenger
    Join Date
    May 2017
    Location
    Brisbane, Australia
    Posts
    26
    Ok, thanks yet again.

    Have done that and will let it run for a while. I did have previous radar number that was 208. Have only activated twice. I am in the Northern Suburbs of Brisbane so there may be quite a few radars.

    If I SSH into the Pi with Putty, and run the command tail /var/log/fr24feed.log, I get the error tail: cannot open '/var/log.fr24feed.log' for reading: No such file or directory. Would this be due to it need to run for a while before it creates a log file?

    Sorry to be a pain.

  2. #12
    Passenger
    Join Date
    May 2017
    Location
    Brisbane, Australia
    Posts
    26
    I am 12NM from Brisbane Airport and directly under the flight path, so it shouldn't take long to register some hits hopefully.

  3. #13
    Super Moderator
    Join Date
    May 2011
    Location
    T-NZCH1, PP:PH New Zealand
    Posts
    5,000
    Typed rather than copy paste?

    You have log. not log/
    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

  4. #14
    Passenger
    Join Date
    May 2017
    Location
    Brisbane, Australia
    Posts
    26
    Corrected that, still same result.

    Will leave it running for an hour or so and see if there is a log created.

  5. #15
    Super Moderator
    Join Date
    May 2011
    Location
    T-NZCH1, PP:PH New Zealand
    Posts
    5,000
    No it won't start after a time - It should be immediate.

    It logs as soon as it starts up if enabled properly

    Double check the 'logging' setting saved (you to need to adjust, save, save, reboot) and hasn't got a different path

    It's under the webpage settings

    fr24log.JPG

    But he also didn't have it quite right if it matches above:

    tail /var/log/fr24feed/fr24feed.log

    Will show the end

    cat /var/log/fr24feed/fr24feed.log

    will show all
    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

  6. #16
    Passenger
    Join Date
    May 2017
    Location
    Brisbane, Australia
    Posts
    26
    Thank you.
    Re did what you suggested.
    the following is in the log:
    pi@raspberrypi:~ $ cat /var/log/fr24feed/fr24feed.log
    2019-01-19 05:51:36 | ______ _ _ _ _ _ _____ ___
    2019-01-19 05:51:36 | | ___|| |(_) | | | | | | / __ \ / |
    2019-01-19 05:51:36 | | |_ | | _ __ _ | |__ | |_ _ __ __ _ __| | __ _ _ __`' / /' / /| |
    2019-01-19 05:51:36 | | _| | || | / _` || '_ \ | __|| '__|/ _` | / _` | / _` || '__| / / / /_| |
    2019-01-19 05:51:36 | | | | || || (_| || | | || |_ | | | (_| || (_| || (_| || | ./ /___\___ |
    2019-01-19 05:51:36 | \_| |_||_| \__, ||_| |_| \__||_| \__,_| \__,_| \__,_||_| \_____/ |_/
    2019-01-19 05:51:36 | __/ |
    2019-01-19 05:51:36 | |___/
    2019-01-19 05:51:36 | [main][i]FR24 Feeder/Decoder
    2019-01-19 05:51:36 | [main][i]Version: 1.0.23-8/generic
    2019-01-19 05:51:36 | [main][i]Built on Oct 11 2018 18:27:28 (HEAD-3c696a7.git/Linux/static_armel)
    2019-01-19 05:51:36 | [main][i]Running on: pi24-raspbian9
    2019-01-19 05:51:36 | [main][i]Local IP(s): 192.168.0.7
    2019-01-19 05:51:36 | [main][i]Copyright 2012-2018 Flightradar24 AB
    2019-01-19 05:51:36 | [main][i]https://www.flightradar24.com
    2019-01-19 05:51:36 | [main][i]DNS mode: PING
    2019-01-19 05:51:36 | [main][i]Automatic updates are ENABLED
    2019-01-19 05:51:37 | ERROR: rmmod: ERROR: Module dvb_usb_rtl28xxu is not currently loaded
    2019-01-19 05:51:37 | [httpd][i]Server started, listening on 0.0.0.0:8754
    2019-01-19 05:51:37 | [main][i]Reader thread started
    2019-01-19 05:51:37 | [main][i]Socket server started
    2019-01-19 05:51:37 | [main][i]MLAT data feed started
    2019-01-19 05:51:37 | [mlat][i]Waiting for MLAT configuration
    2019-01-19 05:51:37 | [bs][i]Initializing server
    2019-01-19 05:51:37 | [bs][i]Starting server on 0.0.0.0:30003
    2019-01-19 05:51:37 | [reader][i]Initializing reader
    2019-01-19 05:51:37 | [reader][i]Connecting to DVBT receiver via (exe:///usr/bin/dump1090-mutability --raw --mlat)
    2019-01-19 05:51:37 | [reader][i]Connected to the receiver, configuring
    2019-01-19 05:51:37 | [reader][i]Configured, processing messages
    2019-01-19 05:51:37 | [master][i]Starting processing thread
    2019-01-19 05:51:38 | [time][i]Synchronizing time via NTP
    2019-01-19 05:51:49 | [time][i]Time synchronized correctly, offset +7.0137 seconds
    2019-01-19 05:51:49 | [feed][i]Downloading configuration
    2019-01-19 05:51:49 | [main][i]Feed Network client started
    2019-01-19 05:51:49 | [feed][d]fetching configuration
    2019-01-19 05:51:50 | [feed][i]configuring decoder
    2019-01-19 05:51:50 | [feed][c]Max range AIR: 350.0nm
    2019-01-19 05:51:50 | [feed][c]Max range GND: 100.0nm
    2019-01-19 05:51:50 | [feed][i]configuration changed
    2019-01-19 05:51:50 | [feed][i]defined 3 servers
    2019-01-19 05:51:50 | [feed][c]Timestamps: optional
    2019-01-19 05:51:50 | [stats][i]Stats thread started
    2019-01-19 05:51:50 | [feed][n]YBBN214@185.218.24.22:8099/UDP
    2019-01-19 05:51:50 | [feed][n]connecting
    2019-01-19 05:51:50 | info | Stopping ReceiverACSender threads for feed
    2019-01-19 05:51:50 | info | Configured ReceiverACSender: 185.218.24.22:8099,185.218.24.23:8099,185.218.24.2 4:8099, feed: YBBN214, send_interval: 5s, max age: 15s, send metadata: true, mode: 1, filtering: true
    2019-01-19 05:51:50 | info | Network thread connecting to 185.218.24.22:8099 for feed YBBN214
    2019-01-19 05:51:50 | [feed][n]connected via UDP (fd 16)
    2019-01-19 05:51:50 | [feed][i]Feed connected
    2019-01-19 05:51:50 | [feed][n]working
    2019-01-19 05:52:02 | [time][w]Time jumped forward by 7.14s, resynchronizing
    2019-01-19 05:52:02 | [time][i]Synchronizing time via NTP
    2019-01-19 05:52:12 | [time][i]Time synchronized correctly, offset -0.0008 seconds
    2019-01-19 05:52:26 | [feed][n]ping 1
    2019-01-19 05:52:27 | [feed][n]syncing stream result: 1

  7. #17
    Passenger
    Join Date
    May 2017
    Location
    Brisbane, Australia
    Posts
    26
    Not sure if this helps at all

    Screen Shot 01-19-19 at 03.56 PM.jpg

  8. #18
    Super Moderator
    Join Date
    May 2011
    Location
    T-NZCH1, PP:PH New Zealand
    Posts
    5,000
    Please paste result of

    cat /etc/modprobe.d/raspi-blacklist.conf
    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

  9. #19
    Passenger
    Join Date
    May 2017
    Location
    Brisbane, Australia
    Posts
    26
    pi@raspberrypi:~ $ cat /etc/modprobe.d/raspi-blacklist.conf
    cat: /etc/modprobe.d/raspi-blacklist.conf: No such file or directory

  10. #20
    Super Moderator
    Join Date
    May 2011
    Location
    T-NZCH1, PP:PH New Zealand
    Posts
    5,000
    what about

    cat /etc/modprobe.d/blacklist-rtl18xxxu.conf

    Possibly the cause of the "ERROR: rmmod: ERROR: Module dvb_usb_rtl28xxu is not currently loaded" error. However we don't want it to be. And it appears to be running fine, but not receiving anything (signal or similar)

    If above doesn't find anything either

    sudo su -
    echo "blacklist r820t" >> /etc/modprobe.d/raspi-blacklist.conf
    echo "blacklist rtl2832" >> /etc/modprobe.d/raspi-blacklist.conf
    echo "blacklist rtl2830" >> /etc/modprobe.d/raspi-blacklist.conf
    echo "blacklist dvb_usb_rtl28xxu" >> /etc/modprobe.d/raspi-blacklist.conf
    echo "blacklist dvb_usb_v2" >> /etc/modprobe.d/raspi-blacklist.conf
    exit

    restart

    Recheck logs
    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •