Page 3 of 5 FirstFirst 12345 LastLast
Results 21 to 30 of 50

Thread: NooElec with small antenna ---> FA Pro Stick + FA 1090 Antenna = worse results?

  1. #21
    Flight attendant Strix technica's Avatar
    Join Date
    Apr 2017
    Posts
    94
    Quote Originally Posted by klinquist View Post
    Ok, I just *also* ordered a SAW filter from Hong Kong .
    Excellent! Can you post a link to its specs? It'll be interesting to compare the two (you should be able to post URLs now, I think).

    Based on what abcd567 said, the FA BP filter is an LC network, and LC networks suck, both in terms of insertion loss and linearity and probably also in terms of phase/group velocity distortion. Not saying SAW or cavity filters are perfect, but both are probably way better than LC networks.

    If the Pro+'s BP filter is also an LC network that might explain why the filter is after the LNA — after all, one of the two principal reasons for using a bandpass filter is to avoid intermodulation in amplifiers — but from this image, I would guess that the Pro+ uses a SAW filter.

  2. #22
    Passenger
    Join Date
    Sep 2016
    Posts
    9
    heh apparently I can't post links in the forum until I have at least 4 posts... so it's ebay item ID 272374693052

    Note I *also* ordered the regular Pro stick w/o the filter.... for even more comparisons.

    Already got too much money on this project .

  3. #23
    Captain abcd567's Avatar
    Join Date
    Sep 2013
    Location
    Toronto CYYZ
    Posts
    2,872
    Quote Originally Posted by Strix technica View Post
    Excellent! Can you post a link to its specs? It'll be interesting to compare the two (you should be able to post URLs now, I think).
    From ebay page http://www.ebay.com/itm/272374693052

    Features:
    The filter bandwidth 8MHz, Cutoff characteristics steep. 1090MHz performance for the ADS-B receiver Optimization,Can effectively filter out-of-band signals,Reduce noise,Increase the dynamic range

    Modell: FBP-1090s
    Impedanz: 50 Ohm
    Mittenfrequenz : 1090 MHz
    Passband : 1086 ~ 1094 MHz
    In-Band-Einfügungsverlust : <3dB
    Maximale Lastleistung : 10 mW (10 dBm)
    Schnittstelle: SMA-M, SMA-F


    If the Pro+'s BP filter is also an LC network that might explain why the filter is after the LNA — after all, one of the two principal reasons for using a bandpass filter is to avoid intermodulation in amplifiers — but from this image, I would guess that the Pro+ uses a SAW filter.
    YES, the ProStick+ (blue) uses a SAW filter, but at wrong location. The SAW filter chip is located between pre-amp and tuner. If it was located between the antenna connector and pre-amp, an external filter will not be required with ProStick Plus (Blue one).
    Last edited by abcd567; 2017-07-17 at 18:10.

  4. #24
    Captain abcd567's Avatar
    Join Date
    Sep 2013
    Location
    Toronto CYYZ
    Posts
    2,872
    Quote Originally Posted by klinquist View Post
    Ok, I just *also* ordered a SAW filter from Hong Kong .
    I have found this one couple of months ago while browsing ebay. I was very much tempted to order it, but it's price prevented me. At US $28.99, it is almost double the price of Flightaware filter (US $15.50).

  5. #25
    Flight attendant Strix technica's Avatar
    Join Date
    Apr 2017
    Posts
    94
    Quote Originally Posted by klinquist View Post
    heh apparently I can't post links in the forum until I have at least 4 posts...
    D'oh! Thought it was 3, but they may have changed that.

    Quote Originally Posted by klinquist View Post
    Note I *also* ordered the regular Pro stick w/o the filter.... for even more comparisons.
    I look forward to hearing your results! Money is tight right now, but I'm awfully tempted to order one of those SAW filters because I'm nearly certain I've got intermod problems.

    Quote Originally Posted by abcd567 View Post
    The filter bandwidth 8MHz, Cutoff characteristics steep.
    Thanks, abcd! Looks like a pretty neat piece of kit, pretty decent insertion loss for a passive filter (< 3dB). If'n I had the money, I'd get one of them and the cavity filter I linked the other day and compare them.

    Quote Originally Posted by abcd567 View Post
    YES, the ProStick+ (blue) uses a SAW filter, but at wrong location. The SAW filter chip is located between pre-amp and tuner.
    Alas... What were they thinking, aside from "ooh, there's a largely empty spot on the PCB where we can glom on a SAW filter for extra mark-up!"?

    Quote Originally Posted by abcd567 View Post
    I have found this one couple of months ago while browsing ebay. I was very much tempted to order it, but it's price prevented me. At US $28.99, it is almost double the price of Flightaware filter (US $15.50).
    You get what you pay for. The FA stand-alone filter, as you pointed out upthread, is a passive LC filter, ie crap.

  6. #26
    Passenger
    Join Date
    Sep 2016
    Posts
    9
    Tonight I installed the "regular" orange FA stick and the FA 1090mhz filter....aaaaaand similar results to the blue stick. Still nowhere near as good as the little antenna with the generic stick! I'm thinking my next move might be to order an adapter to hook the generic stick to the FA antenna to see if the issue is with the antenna or not.

    Here's the setup (note the "better" 1090mhz filter has not yet arrived)

    IMG_9636.jpg
    Last edited by klinquist; 2017-07-20 at 03:59.

  7. #27
    Captain Anmer's Avatar
    Join Date
    Apr 2010
    Posts
    1,384
    The test I suggested earlier is to try the FlightAware Pro Sticks with the antenna that cam- e with the generic stick and then the generic stick with the FA antenna and cable.

    What spec cable are you using with the FA external antenna? Did it come with pre-installed connectors?
    Mike


    www.radarspotting.com

    Radarspotting since 2005

  8. #28
    Flight attendant Strix technica's Avatar
    Join Date
    Apr 2017
    Posts
    94
    Yeah, I think trying the old antenna with the FA stick and visa versa is definitely worth doing, as is giving some thought to the coax feeder. Golden rule of experimentation: change only one thing at a time.

    Golden rule of debugging something: start with what once worked, and reintroduce elements until it breaks, don't try to go from what's broken to what works because if there's more than one thing wrong, a problem fixed can remain masked by others and you won't even know that you did, in fact, fix a problem.

    Unless your coax run is very short, then consider that a third variable. Remember that different coax has different amounts of loss per metre, but I'd be surprised if the supplied antenna was fed with anything other than RG58 (or maybe RG59) which is about the worst coax commonly found. But even then, not all RG58 is created equal either. Some of it's rubbish, some of it's okay (depending on application).

    In theory, impedance mismatches will make things worse even for rx-only, but there isn't much you can do about that except not make it worse. At least in the generic SDR case, the receiver is designed for a 75Ω feed, yet the connectors used are typically 50Ω. (In practice, that impedance mismatch loss is only about -1 dB, but you don't want to switch between impedances more often than you have to.) In the FA case, the LNA might actually be 50Ω in which case mismatch loss hardly matters because the signal will be plenty strong enough by the time it reaches the 75Ω R820T2 RF mixer, and low-loss 50Ω RG-8 to a 50Ω antenna would be ideal.

    Your antenna has a characteristic impedance also. Whips range between 36–50Ω, dipoles are about 72Ω. In practice, dielectric loss is going to be more of a problem that mismatch loss, but it's as well to bear it in mind. Just don't constantly switch back and forth between impedances any more than you have to.

    Quote Originally Posted by klinquist
    Tonight I installed the "regular" orange FA stick and the FA 1090mhz filter....aaaaaand similar results to the blue stick.
    Which is no surprise if the problem is intermod noise. As I said, the FA BP filter's bandwidth is too wide to exclude all of GSM, especially in North America and the in-line filter is a crappy LC network rather than a SAW or cavity filter.

    If you're running dump1090-mutability or equivalent, have a look at the range of signal strengths it reports. My Munin plugins are good for this, but most of those only work with -mutability. If your peak signal stays stuck at > -5 dBFS all day and night, and your mean signal is around -10 dBFS, your gain is probably too high.

  9. #29
    Captain abcd567's Avatar
    Join Date
    Sep 2013
    Location
    Toronto CYYZ
    Posts
    2,872
    Try Gain 30 dB.
    Users having FA Antenna and Pro Stick /Pro Stick Plus, generally use gain between 25 dB and 35 dB.
    I use 28 dB with one receiver, and 30 dB with other one.

    Python Script to optimize gain is a help, but dont give any concrete value. Finally it is trial and error to find best gain.

    Code:
    pi@raspberrypi:~ $ sudo nano /etc/default/dump1090-mutability
    Above command will open file in nano editor
    Press Ctrl+W (i.e. Find), then type GAIN= and press Enter Key. The cursor will jump to GAIN=
    Change the gain value (shown in red)
    Save file (Ctrl+o), then close the file and exit editor (Ctrl+x)

    .....................
    .....................
    .....................
    # Receiver options
    #

    # RTLSDR device index or serial number to use
    # If set to "none", dump1090 will be started in --net-only mode
    DEVICE=""

    # RTLSDR gain in dB.
    # If set to "max" (the default) the maximum supported gain is used.
    # If set to "agc", the tuner AGC is used to set the gain.
    GAIN=30

    # RTLSDR frequency correction in PPM
    PPM="0"
    .....................
    .....................
    .....................

    Now restart dump1090 for new value of gain to take affect.
    Code:
    sudo systemctl restart dump1090-mutability
    Now check the status. It will show the gain value in use. This value will be retained on reboots and restarts, unless you change it.
    Code:
    pi@raspberrypi:~ $ sudo systemctl status dump1090-mutability -l
    Last edited by abcd567; 2017-07-20 at 15:30.

  10. #30
    Passenger
    Join Date
    Sep 2016
    Posts
    9
    Quote Originally Posted by Anmer View Post
    What spec cable are you using with the FA external antenna? Did it come with pre-installed connectors?
    I'm using this one:
    https://www.amazon.com/gp/product/B0...?ie=UTF8&psc=1


    So last night I connected the yellow FA stick directly to the antenna with NO filter and it seems that I'm getting significantly better results - even saw one aircraft 160nm away. This was using dump1090 with completely default settings.
    I'm running the gain python test now to figure out the ideal gain and see how much better I can do.... but it seems that any of the filters I've tried so far (the one built into the blue stick and the external one) are making things worse. Odd, I know!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •