Page 8 of 11 FirstFirst ... 678910 ... LastLast
Results 71 to 80 of 103

Thread: How to Install dump1090-mutability_1.15~dev on RPi

  1. #71
    Flight attendant
    Join Date
    Jan 2015
    Location
    T-EGKK39
    Posts
    64
    Thanks abcd567, another Pi set up and running all three clients. I had to install dirmngr separately but that sounds like a Debian change..?

  2. #72
    Passenger thehague's Avatar
    Join Date
    Aug 2017
    Location
    Randstad
    Posts
    17
    Quote Originally Posted by sebasuchan View Post
    Hello Captain, I have installed and followed the installation guide with a fresh install and I have the same problem than DimDim
    Problem fetching data from dump1090.
    AJAX call failed (error: Not Found). Maybe dump1090 is no longer running?
    The displayed map data will be out of date
    I can't send data to FR24, PlaneFinder, Flightaware
    unknown version of DUMP1090 after install
    Quote Originally Posted by Dimdim View Post
    Hi,

    I have followed almost all the steps until instaling fr24. So far everthings is working except the gmap.html.
    I think the error lies under the second clock. Unkown version.

    Problem fetching data from dump1090.
    AJAX call failed (error: Not Found). Maybe dump1090 is no longer running?
    The displayed map data will be out of date.


    Attachment 8848
    Try this:
    Code:
    #open file rtl-sdr-blacklist.conf for editing
    sudo nano /etc/modprobe.d/rtl-sdr-blacklist.conf
    
    #add the following 2 lines to above file:
    blacklist dvb_usb_rtl2832u
    blacklist dvb_usb
    
    #save file
    
    #get the vendor and product ID from your USB receiver
    lsusb
    
    #note that line which is related to your stick (e.g. Bus 003 Device 018: ID 0bda:2832 Realtek Semiconductor Corp. RTL2832U DVB-T)
    
    #open file rtl-sdr.rules for editing
    sudo nano /etc/udev/rules.d/rtl-sdr.rules
    
    #add the following line to above file and change the id's (e.g.):
    SUBSYSTEMS=="usb", ATTRS{idVendor}=="0bda", ATTRS{idProduct}=="2832", MODE:="0666" -
    
    #save file
    #exit and reboot
    sudo reboot
    Last edited by thehague; 2017-08-30 at 21:31.

  3. #73
    Passenger thehague's Avatar
    Join Date
    Aug 2017
    Location
    Randstad
    Posts
    17
    Quote Originally Posted by sebasuchan View Post
    It works. Thank you very much for these lines of code
    Quote Originally Posted by Dimdim View Post
    Thank you so much thehague.
    It works!!!
    You're welcome.

  4. #74
    Captain abcd567's Avatar
    Join Date
    Sep 2013
    Location
    Toronto CYYZ
    Posts
    2,206
    If you are using Raspbian STRETCH, you will get this notice on map:
    Problem fetching data from dump1090.
    AJAX call failed (error: Not Found). Maybe dump1090 is no longer running?
    The displayed map data will be out of date
    • The solution is to add a file "rtl-sdr.rules" with proper entries in folder /etc/udev/rules.d

    • Blacklisting is NOT required.


    Use this simple one-step solution:
    Code:
    sudo wget -O  /etc/udev/rules.d/rtl-sdr.rules "https://raw.githubusercontent.com/osmocom/rtl-sdr/master/rtl-sdr.rules"
    
    sudo reboot
    NOTE:
    I have worked out the bove simplified solution based on solutions posted by jaxxtheone, Randstad, and thehague.
    Last edited by abcd567; 2017-09-01 at 22:10.

  5. #75
    Captain abcd567's Avatar
    Join Date
    Sep 2013
    Location
    Toronto CYYZ
    Posts
    2,206
    [SOLVED] BUGS IN RASPBIAN STRETCH [SOLVED]

    (1) dump1090-mutability fails to open DVB-T. Gives following error:
    Code:
    Problem fetching data from dump1090.
    AJAX call failed (error: Not Found). Maybe dump1090 is no longer running?
    The displayed map data will be out of date.
    Reason: Missing rtl-sdr.rules.


    Workaround:
    Code:
    sudo wget -O  /etc/udev/rules.d/rtl-sdr.rules "https://raw.githubusercontent.com/osmocom/rtl-sdr/master/rtl-sdr.rules"
    
    sudo reboot
    .
    .
    .

    (2) FlightRadar24's fr24feed fails to install by bash script.

    Reason: Missing package "dirmngr".


    Workaround:
    Code:
    sudo apt-get update
    sudo apt-get install dirmngr
    
    sudo bash -c "$(wget -O - http://repo.feed.flightradar24.com/install_fr24_rpi.sh)"
    #Enter details when prompted.
    .
    .
    .

    (3) RadarBox24's rbfeeder fails to install by bash script
    Code:
    sudo bash -c "$(wget -O - http://apt.rb24.com/inst_rbfeeder.sh)"
    .........
    W: GPG error: http://apt.rb24.com jessie Release: The following signatures were invalid: A7E7D5E3786CA2212A3A5F4769D62C99357DF51A
    W: The repository 'http://apt.rb24.com jessie Release' is not signed.
    .........
    WARNING: The following packages cannot be authenticated!
      rbfeeder
    .....
    Failed to start rbfeeder.service: Unit rbfeeder.service not found.

    Workaround:
    Code:
    sudo apt-get update
    sudo apt-get install rbfeeder
    Ignore following warning during install and say y
    Code:
    WARNING: The following packages cannot be authenticated!
      rbfeeder
    Install these packages without verification? [y/N]
    Last edited by abcd567; 2017-09-21 at 21:23.

  6. #76
    Passenger
    Join Date
    Jan 2018
    Posts
    1
    I get up to step 11 ok then when I do the command,
    I keep getting failed to start the dirmngr ‘/USA/bin/dirmngr’ no such file or directory name.

    Any thoughts of what I am doing wrong? I am still learning Linux so am sure I am just missing something.

  7. #77
    Captain abcd567's Avatar
    Join Date
    Sep 2013
    Location
    Toronto CYYZ
    Posts
    2,206
    @HAm

    A wild thought. Try this.
    -The first command will install dirmng, essential for installation of fr24feed, if not yet installed.
    -The second command will download the .deb package for armhf (armv6l & armv7l).
    -The third command will try to install it.
    It may be possible that armv6l/armv7l and arm64 are not very different, and this package gets installed successfully on your "Le Potato"
    No harm in trying.

    Code:
    sudo apt-get install dirmngr
    
    sudo wget http://repo.feed.flightradar24.com/rpi_binaries/fr24feed_1.0.19-15_armhf.deb
    
    sudo dpkg --install fr24feed_1.0.19-15_armhf.deb

    Additional command in case of failure (to fix a broken install):
    Code:
    sudo dpkg --configure -a
    Last edited by abcd567; 2018-02-15 at 17:14.

  8. #78
    Passenger
    Join Date
    Apr 2015
    Location
    Smedsby, Korsholm, Finland
    Posts
    17
    @abcd567
    That was exactly what i thought from the very beginning but the Le Potato did not boot at all.
    The cpu in Le Potato is an AML-S905X-CC and Raspberry 3 has an ARM Cortex A53
    There must be some difference in the settings in Raspbian that prevents the Le Potato from starting. I have to look a little deeper into that.
    But for the moment being I feel pleased having the 64 bit Ubuntu Xenial up and running and accepting the 32 bit fr24feed
    -Hans

  9. #79
    Captain abcd567's Avatar
    Join Date
    Sep 2013
    Location
    Toronto CYYZ
    Posts
    2,206
    Currently dump1090-mutability uses Open Steert Map.

    If someone wants dump1090-mutability v1.15~dev which has Google map, he has to install an older version which was released earlier than the switch to Open Street map. Here is how to do this:

    Step-By-Step Method for Installing June 8, 2016 version of dump1090-mutability v1.15~dev (The last version which had Google Map).

    STEP-1: Install build tools and dependencies
    Code:
    $ sudo apt-get update
    $ sudo apt-get install librtlsdr-dev libusb-1.0-0-dev pkg-config debhelper
    $ sudo apt-get install lighttpd 
    $ sudo apt-get install git

    STEP-2: Clone source code from GitHub
    Code:
    $ git clone https://github.com/mutability/dump1090.git
    $ cd dump1090

    STEP-3: Reset git to the last version which had Google Map.
    Code:
    $ git reset --hard dfe3d7af12
    HEAD is now at dfe3d7a Merge pull request #126 from rxseger/osx

    STEP-4: Build .deb package from source code
    Code:
    $ sudo dpkg-buildpackage -b

    STEP-5: Install the .deb package
    Code:
    $ cd ../
    $ sudo dpkg --install dump1090-mutability_1.15~dev_armhf.deb
    $ sudo lighty-enable-mod dump1090
    $ sudo /etc/init.d/lighttpd force-reload

    STEP-6: Configure settings
    Code:
    $ sudo dpkg-reconfigure dump1090-mutability
    $ sudo systemctl restart dump1090-mutability
    $ sudo reboot

    STEP-7: Enjoy the Google Map
    dump1090-mutability-GoogleMap-Commit 8 June 2016.png

  10. #80
    Passenger
    Join Date
    Aug 2017
    Posts
    3
    I hope someone can help me. I did everything like it is written in the first post.
    FR24 - works
    planefinder - works
    PiAware - does not work

    I am not able to configure piaware, cant even reach it via port 8080 in my browser.

    Yesterday I did the same and before installing planefinder I configured PiAware. But also yesterday I was not able to reach piaware on port 8080.

    Can somebody help me?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •