Announcement

Collapse
No announcement yet.

Windows Setup/Feed Migration (virtualVM) Assistance

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Code:
    sudo mkdir /var/log/fr24feed
    Last edited by abcd567; 2019-06-23, 22:44.

    Comment


    • Originally posted by abcd567 View Post
      Code:
      sudo mkdir /var/log/fr24feed
      Thank you

      fr24feed was set

      Comment


      • Originally posted by wiedehopf View Post
        It's very confusing, in the 2nd picture you posted, the package in question is being downloaded.

        So i'm not sure how it could be not working?
        Maybe try

        sudo apt clean

        Then try the install again.
        Thank you for help

        Comment


        • For the logs to work properly you might need to do this:

          sudo chown fr24 /var/log/fr24feed

          That way fr24feed can write to that directory.
          But if you don't need the logs anyway it doesn't matter.

          Comment


          • Hi

            on the usb panel on dashboard, the red circle flashes and the connection between the dongles and the operating system is not established, like this:

            Untitled.jpg

            & when in type fr24feed-status, i got this massage:

            Receiver:down ... failed

            fr24MLAT : not running ....failed
            Last edited by arash; 2019-06-24, 20:12.

            Comment


            • Originally posted by arash View Post
              Hi

              on the usb panel on dashboard, the red circle flashes and the connection between the dongles and the operating system is not established, like this:

              [ATTACH=CONFIG]10827[/ATTACH]

              & when in type fr24feed-status, i got this massage:

              Receiver:down ... failed

              fr24MLAT : not running ....failed
              Your original said it works fine and then does that? If so, software can't fix this. Your stick is going faulty and windows can't see it anymore

              Sent from my EML-L09 using Tapatalk
              Posts not to be taken as official support representation - Just a helpful uploader who tinkers

              Comment


              • .


                Is My DVB-T RTL SDR Dongle Healthy?

                .

                Comment


                • Originally posted by arash View Post
                  Hi

                  on the usb panel on dashboard, the red circle flashes and the connection between the dongles and the operating system is not established, like this:

                  [ATTACH=CONFIG]10827[/ATTACH]

                  & when in type fr24feed-status, i got this massage:

                  Receiver:down ... failed

                  fr24MLAT : not running ....failed
                  Possibly your Dongle is NOT attached to the VM. You have to attach it.
                  The two screenshots below give steps to attach the dongle (steps 1 to 7):

                  VM USB -1.pngVM USB -2.png

                  Comment


                  • Originally posted by abcd567 View Post
                    Possibly your Dongle is NOT attached to the VM. You have to attach it.
                    The two screenshots below give steps to attach the dongle (steps 1 to 7):

                    [ATTACH=CONFIG]10859[/ATTACH][ATTACH=CONFIG]10860[/ATTACH]
                    After this, https://forum.flightradar24.com/thre...l=1#post122373

                    I questioned if the stick is wedging and going offline. As it seems to work, then not. So he reinstalled to try 'fix' and made things worse
                    Posts not to be taken as official support representation - Just a helpful uploader who tinkers

                    Comment


                    • Originally posted by Oblivian View Post
                      After this, https://forum.flightradar24.com/thre...l=1#post122373

                      I questioned if the stick is wedging and going offline. As it seems to work, then not. So he reinstalled to try 'fix' and made things worse
                      So what can I do to fix this problem?

                      Comment


                      • Originally posted by abcd567 View Post
                        Possibly your Dongle is NOT attached to the VM. You have to attach it.
                        The two screenshots below give steps to attach the dongle (steps 1 to 7):

                        [ATTACH=CONFIG]10859[/ATTACH][ATTACH=CONFIG]10860[/ATTACH]
                        I do all the steps according to the instructions.

                        Comment


                        • Originally posted by abcd567 View Post
                          Instead of this picture:

                          Zadig-3.png

                          I see this:

                          zad4.jpg

                          you can see the USB ID is ok.

                          also, when I run rtl_test.exe, I got this massage:

                          zad5.jpg

                          Comment


                          • Originally posted by arash View Post
                            So what can I do to fix this problem?
                            It is still not clear to us. Please explain more


                            Does it work at all
                            Does it start to work then stop

                            What stick is it

                            If you look at windows device manager. Do you see it.

                            Does dump1090 under windows (not the VM) work

                            Dump1090 is a popular command line ADS-B decoder which many people believe has superior decoding performance compared to other decoding software. Previously it has only been available for Linux and Mac operating systems, however recently it has been updated with a Windows command line version. The most up to date branch of dump1090 can be downloaded from GitHub here. To install dump1090 on Windows follow these steps: Download the dump1090 zip file from the GitHub download link. Download the official RTL-SDR Windows release from http://sdr.osmocom.org/trac/attachment/wiki/rtl-sdr/RelWithDebInfo.zip. Copy the libusb-1.0.dll, rtlsdr.dll and pthreadVC2-w32.dll files from the official RTL-SDR Windows release zip file to


                            Sent from my EML-L09 using Tapatalk
                            Posts not to be taken as official support representation - Just a helpful uploader who tinkers

                            Comment


                            • Originally posted by Oblivian View Post
                              It is still not clear to us. Please explain more


                              Does it work at all
                              Does it start to work then stop

                              What stick is it

                              If you look at windows device manager. Do you see it.

                              Does dump1090 under windows (not the VM) work

                              Dump1090 is a popular command line ADS-B decoder which many people believe has superior decoding performance compared to other decoding software. Previously it has only been available for Linux and Mac operating systems, however recently it has been updated with a Windows command line version. The most up to date branch of dump1090 can be downloaded from GitHub here. To install dump1090 on Windows follow these steps: Download the dump1090 zip file from the GitHub download link. Download the official RTL-SDR Windows release from http://sdr.osmocom.org/trac/attachment/wiki/rtl-sdr/RelWithDebInfo.zip. Copy the libusb-1.0.dll, rtlsdr.dll and pthreadVC2-w32.dll files from the official RTL-SDR Windows release zip file to


                              Sent from my EML-L09 using Tapatalk
                              yes it work when I use it to run SDRsharp.

                              as I described on post #260, the the red circle start to flash & never stop.

                              Which version should I download for Windows 7?

                              6.jpg

                              I got this massage when start dump1090.bat:

                              7.jpg
                              Last edited by arash; 2019-07-07, 22:25.

                              Comment


                              • Maybe in the Zadig drop down menu actually select the USB stick instead of the "bulk interface"?

                                Comment

                                Working...
                                X