Search:

Type: Posts; User: wiedehopf

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. If you want to use the armhf binary (most current...

    If you want to use the armhf binary (most current version), then you will need to use the Raspbian Desktop image (it's for x86/amd64 computers), it has some sort of emulation built in for armhf...
  2. If you are using dump1090, use beast-tcp like...

    If you are using dump1090, use beast-tcp like this:



    receiver="beast-tcp"
    fr24key="xxxxxxxxxxxxxxxx"
    host="127.0.0.1:30005"
    bs="no"
    raw="no"
  3. Replies
    7
    Views
    200

    The kernel has drivers for the device to use it...

    The kernel has drivers for the device to use it as an DVB-T receiver to watch digital terrestially broadcast television.

    Those drivers use the device and it can't be used by dump1090....
  4. dump1090 provides beast protocol output over TCP...

    dump1090 provides beast protocol output over TCP port 30005.

    The most current version is only available for the armhf architecture.
    You can't run binaries from other architectures. (Or at least...
  5. Replies
    71
    Views
    6,508

    Ctrl-C to interrupt programs and get back to the...

    Ctrl-C to interrupt programs and get back to the shell. Doesn't always work.

    In many programs just pressing Q for quit will make them exit.
  6. Replies
    7
    Views
    200

    If you have lighttpd running, it should be at...

    If you have lighttpd running, it should be at /dump1090-fa

    I'd recommend my improved interface: https://github.com/wiedehopf/tar1090#tar1090

    It even offers some advice on how to configure it...
  7. Replies
    7
    Views
    200

    --status is not recognized It's just starting...

    --status is not recognized

    It's just starting up the application, but the service is already running the application.

    pgrep -a dump1090
    pgrep -a fr24feed

    With those commands you will see...
  8. Replies
    7
    Views
    200

    Wrong command, use: fr24feed-status Stop...

    Wrong command, use:

    fr24feed-status

    Stop writing in multiple threads, it's really annoying.
  9. I didn't say it would work. It's for the...

    I didn't say it would work. It's for the Raspberry Pi where packages are available.

    I pointed you at how to compile dump1090-fa.
    Also pointed you at how to configure fr24feed.

    That's what you...
  10. Yes you need dump1090, it's the software that...

    Yes you need dump1090, it's the software that connects to the dvb-t stick / rtl-sdr dongle.


    What you have used before was fr24feed automatically starting dump1090.
    That's not gonna work with...
  11. You need dump1090, i'd recommend dump1090-fa. ...

    You need dump1090, i'd recommend dump1090-fa.

    Or what is your receiver hardware?
  12. This may give you a few pointers on compiling and...

    This may give you a few pointers on compiling and installing dump1090-fa:

    https://github.com/wiedehopf/adsb-wiki/wiki/Building-dump1090-fa-from-source

    Depending on your version of debian, you...
  13. Replies
    1,272
    Views
    2,848,248

    It should work fine on the piaware image. (Did...

    It should work fine on the piaware image. (Did you run the fr24feed install script for RPi?)

    The required fr24feed settings are explained here:...
  14. Replies
    71
    Views
    6,508

    Latitude is normally negative in Australia, so...

    Latitude is normally negative in Australia, so you want -27 ;)

    https://www.mapcoordinates.net/en

    I'm not sure if you can change units in dump1090-mutability, you can in dump1090-fa though....
  15. Thread: best antenna

    by wiedehopf
    Replies
    2,839
    Views
    3,970,500

    Copper oxide on the surface won't degrade the...

    Copper oxide on the surface won't degrade the antenna.

    You might want to experiment with bending the top 0.5 to 1cm over, my spider needed quite a bit shorter of a whip to have optimal reception.
  16. Replies
    71
    Views
    6,508

    Work on Putty first....

    Work on Putty first. https://discussions.flightaware.com/t/for-beginners-how-to-ssh-to-rpi-setup-putty-in-windows/44432

    Massively more convenient than having to have an extra keyboard/monitor....
  17. Replies
    71
    Views
    6,508

    RW? What do you mean?

    RW? What do you mean?
  18. Replies
    71
    Views
    6,508

    Having more space doesn't hurt, expand away. ...

    Having more space doesn't hurt, expand away.

    If you don't have SSH access already, you will want to enable it in that menu.
    Maybe set your timezone?

    I'm partial to the tools below because i...
  19. Replies
    3
    Views
    236

    Which LNA did you get? They have a filtered...

    Which LNA did you get?

    They have a filtered and unfiltered one.

    With the unfiltered one all signals are gonna be stronger, so that's what you see on the scan.
    If it's the filtered one you...
  20. I suppose with config dvb-t it might be...

    I suppose with config dvb-t it might be sufficient to do:

    sudo systemctl disable --now dump1090-mutability
    sudo systemctl restart fr24feed

    This should disable the dump1090 autostart and stop...
  21. To be honest i don't care, i just post my script...

    To be honest i don't care, i just post my script mostly and hope people like the added interfaces ;)
  22. You probably have dump1090 starting on its own...

    You probably have dump1090 starting on its own and additionally are using receiverd dvb-t.

    With dvb-t fr24feed wants to start dump1090 itself, it must not be started before.
    Other option is...
  23. Replies
    71
    Views
    6,508

    if you clamp down the RG-6 coax, you can get away...

    if you clamp down the RG-6 coax, you can get away with having the cable not be flexible.
  24. Replies
    71
    Views
    6,508

    You can even build it at the end of the RG-6 run...

    You can even build it at the end of the RG-6 run without any extra connectors.

    Just need an connector/adapter to connect to the dongle.
  25. abcd is correct, i neglected to add code tags :)...

    abcd is correct, i neglected to add code tags :)

    Anyway if dump1090 starts on its own, you need to change the configuration as described.

    I'm sure you'll have the problems resolved soon.
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4