abcd567
Captain

Flightaware ProStick Plus at Amazon . com https://www.amazon.com/dp/B01M7REJJW/

If you use Flightaware blue dongle, you will not need a satellite amplifier (unless your coax cable is too long).

As with dipole you are using dvbt (no integral amplifier), better add a Satellite amplifier close to the antenna. You will need a power inserter and...

Try different gain value, like 49 45 40, 35 etc, and at each value observe message rate / number of planes to find best setting. Alternatuvely...

The EB_VERSION is same as mutability ver 1.15~dev. It is a built package maintained in Debian Buster repository by Debian hamradio maintener. It is...

Which version of dump1090 you have? - dump1090-mutability ver 1.14 - dump1090-mutability ver 1.15~dev - dump1090-fa .

If you have a long coax, and prostick is at other end of coax, it may be beneficial to add a satellite LNA (or any other LNA) near the antenna. ...

AlejandroM Please see my post again. I have edited it. If you look at the timings, my edit (19:28) & your post (19:28) crossed. :)

Please see attached photos in this post: https://forum.flightradar24.com/threads/3831-best-antenna?p=38188&viewfull=1#post38188 You will note I...

AlejandroM: Do I need a Filter? - Find RF Signals In Area

Done in correct sequence for a freshly written Raspbian image.

There are two scripts for installing ver 1.15. Script (1) - Replacement of ver 1.14 by ver 1.15: This works only after fr24 script has been run...

Strange! That script does NOT do anything other than replacing old version of dump1090 by new version. It does not touch WiFi.

YES, you can, even if you dont have Pi24 OS, and have installed (fr24 feeder+dump1090 ver 1.14) by FR24 script.

Thanks Oblivian for changing title of this thread, and deleting the duplicate thread.

Updated on August 13, 2019. In first post, added Automated Installation by bash script

Use Bitvise ssh CLIENT. It has both SSH window like PuTTY, and a SFTP file transfer window like FileZilla. https://www.bitvise.com/ssh-client ...

Wiedehop has recently written a script which installs graphs only (no web portal). Give a look here: ...

Hi mgunther! Nice to see you after a long gap. If I remember correctly, you were the key contributer to "Adsb-receiver Project" during the stage J...

This is fr24feed's configuration with dump1090-mutability ver 1.15~dev installed by user: "http://IP-of-Pi:8754/settings.html"

iam_carnage: fr24rwbuck: You both have dump1090-mutability ver 1.14 (Pi24 image / setting receiver = DVB-T) Go to this post: 2019 - PI24...

"Active Diapason" Antenna (1090 MHz) This antenna uses design by F5ANN (Francois) November 2014: Antenna design posted by F5ANN (Francois) in...

LNA: The LNA is inside the antenna. You dont see it. The LNA gets 5V DC power through the antenna cable. Bias-t: It feeds 5V DC power to antenna...

(1) Map is available at following address when Default Settings are used: "http://ip-of-pi/dump1090/gmap.html" AND ...

pi@raspberrypi:~ $ cat /etc/lighttpd/lighttpd.conf server.modules = ( "mod_indexfile", "mod_access", "mod_alias", ...

pi@raspberrypi:~ $ sudo nano /etc/lighttpd/conf-available/89-dump1090.conf # Allows access to the static files that provide the dump1090 map view,...

The mr-dump1090 uses its integral webserver, and by default serves map at port 8080. This can be changed to another port number by argument...

I dont see anything in this photo which points to poor performance, or may be my eyesight not so good. What I missed?