Announcement

Collapse
No announcement yet.

AERIAL RECIEVING

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • milair
    replied
    Originally posted by HermanZA View Post
    Very nicely done, Milair! You can market those (at a slight profit!)
    Thanks, but not possible I'm afraid as they are not legally CE marked, so if I sold these in UK or Europe I could be prosecuted under EU law. The fixing method is a bit of a bodge, so I would have to make something a bit better anyway

    John

    Leave a comment:


  • HermanZA
    replied
    Very nicely done, Milair! You can market those (at a slight profit!)

    Leave a comment:


  • milair
    replied
    Originally posted by CRC View Post
    milair: Great, thanks! It looks like a BAV99 style diode. As I said, hopefully mine have those already fitted.. Otherwise I'll have to engineer them on there myself
    I've brought 5 units now from various Far East EBay sellers, all cost around 7, in fact the last two I got for 0.01 + 4.99 postage from Singapore !

    If they look like the same as in the picture and come with a remote control and mag mount antenna they should hopefully be identical inside. I remove mine from the case, cut out the IR receiver sensor and mount it in a diecast box, with thermal gap pad between the bottom of the PCB and the box to dissipate heat. I then get a MCX to BNC pigtail cable on EBay and mount this to one side of the box. Lastly remove the USB plug and cut a standard USB cable to bare wires and solder to the pads where the USB plug was. I then remove the LED and extend the wires allowing it to be fitted in the case through a 3mm hole. A couple of metal brackets tapped M4 on the top with more thermal gap pad hold it all in place.

    CIMG0396.jpg

    Go on be brave !

    John
    Last edited by milair; 2014-02-03, 20:39.

    Leave a comment:


  • CRC
    replied
    milair: Great, thanks! It looks like a BAV99 style diode. As I said, hopefully mine have those already fitted.. Otherwise I'll have to engineer them on there myself

    Leave a comment:


  • milair
    replied
    Originally posted by CRC View Post
    milair: Any chance of some photos?
    Here you go, the diode is between the mark for C13 and the IR receiver diode (3 legs)

    CIMG0393.jpgCIMG0394.jpg

    Leave a comment:


  • CRC
    replied
    milair: Any chance of some photos?

    Leave a comment:


  • milair
    replied
    Originally posted by CRC View Post
    Yeah... I've got another couple of RTL2328u based tuners on the way from China now... I've also sourced a local supplier of BAV99 protection diodes in case these tuners don't have them fitted (like my now dead ones). These ones use the newer R820T tuner - which may be better than the E4000 ones. Maybe. Time will tell when they get here...
    All the R820T ones I've brought on Ebay from China have the diode present, they have a radius edge on two sides of the case, and an mcx connector. All have the China Export logo not the EU CE mark as well.

    John

    Leave a comment:


  • CRC
    replied
    Yeah... I've got another couple of RTL2328u based tuners on the way from China now... I've also sourced a local supplier of BAV99 protection diodes in case these tuners don't have them fitted (like my now dead ones). These ones use the newer R820T tuner - which may be better than the E4000 ones. Maybe. Time will tell when they get here...

    Leave a comment:


  • peterhr
    replied
    have a look at the best antennas thread http://forum.flightradar24.com/threa...1-best-antenna (sorry it is long) - some of the best antenna have a shorted 1/4 wave whip at the end or some shorted matching stub, that means the inner and the outer of the co-ax are shorted together as far as a DC voltage is concerned, though they are optimally tuned for the extraction of the desired signal.

    Leave a comment:


  • CRC
    replied
    HermanZA: Could be - the poles are on the ridgeline of the roof - so there is no way to ground the pole itself. I agree this wouldn't make matters easy - however proper ESD in the device would still prevent issues....

    EDIT: Thinking further, earthing the pole would only earth the coax sheath - not the centre conductor (otherwise the antenna wouldn't work!) but maybe its just enough to not damage the equipment....

    Leave a comment:


  • HermanZA
    replied
    I am running 2 sticks as well, one for ADS-B and other for radio reception... both made in and ordered from China, and no problem thus far. My installation poles here are earthed / direct grounded, so there should not be any static build up on the antenna. CRC: Not sure if your installation is earthed, as that could be the cause of ES build up on the antenna itself and then frying your dongle.
    Last edited by HermanZA; 2014-01-31, 23:42.

    Leave a comment:


  • CRC
    replied
    The ESD protection is a single component. It can be added on afterwards - but the spot for it is left blank in most tuners I've come across. You may be lucky and have one with the single ESD protection component installed on the board.

    Leave a comment:


  • Amper
    replied
    2 in one week...hm....


    My "made in china" 5$ dongle hardly has any protection.....don't even know what model it is...
    Last edited by Amper; 2014-01-31, 23:11.

    Leave a comment:


  • CRC
    replied
    It depends on your device... As I said, *SOME* have them fitted, most don't. You may just be lucky. I've now fried two this week. A google for your type of stick + ESD will hopefully show if your device has ESD protection built in or not. Also try the keyword BAV99 (which is an ESD protection diode type).

    Leave a comment:


  • Amper
    replied
    i have rtl device with 2 outdoor (j-pole and co-co)antenna and works perfectly for 4 months now with no protection
    Last edited by Amper; 2014-01-31, 22:40.

    Leave a comment:

Working...
X