Originally posted by paradiselost
View Post
Announcement
Collapse
No announcement yet.
PHILIPPINE RADAR FORUM
Collapse
X
-
Originally posted by hacker.ph View PostYou can get the adapters at Lazada. Expect 1-3 weeks delivery since most of the connectors are shipped from China. They have almost everything (sma, bnc, n, uhf etc..) and they deliver door to door.
There is also a small idiosyncrasy with the FIBR modem. If you connect lan1 to your pc or laptop and a device like your RPI to lan2 they both will have interactive access to the internet.....but they won't be able to interact with each other.
Since I have lots of devices I connect to lan1 to a gigabyte switch and to the switch the pc and devices....now all the devices are available to the pc or laptop and you can run programs like VirtualRadar. Several of the computer stores like Octagon have them for about P1600 or so. The one I use is a D-Link 8 port switch.
If you are running a server from your pc and you have a dynamic WAN IP since I use NO-IP in the NO-IP configuration I enter the local IP of the PC which I have made static. It won't work if your server is set to automatic addressing. Folks from the internet will get the error.
Again, wish you luckLast edited by paradiselost; 2019-01-03, 04:31.
Comment
-
Hi John, I thought it might be Milton from the Paradise Lost connection. OK I dragged the position of your base to my location and it drew a new plot. I expected it to give me a new ID. It didnt, I'll have to start fresh. Hope it didnt disturb your data. Try this one titled Hillsview rooftop http://www.heywhatsthat.com/?view=MW2BGVMP
I've ordered a SMA connector from Lazada, but dont have much confidence in their delivery from previous experience.
Interesting setup you have, I will examine the details more closely. At home in the UK I have allocated a static IP to the RPi from my router and it works fine. The PLDT router doesn't give such flexibility, in fact its locked down so that you can't make any admin changes except the wifi name. But I'm working on it.
Comment
-
Originally posted by hacker.ph View PostYou antenna setup looks nice.. How long is the mast? Is it 6meters? Are you using gi or stainless pipes? Is the mast 1.5 or 2"
In over 2 years the only problem I have encountered is AC adapters sometime fail from thermal or other causes. Each time FR24 Support supplied replacements when I couldn't get them off the shelf locally. From January of last year I began noticing reduced range for the FR24 receiver until the range dropped down to 50 miles. Suspecting either antenna or coax problems FR24 shipped a replacement set. It took a long time to arrange for climbers but when we replaced the antenna and coax normal range continued. With the antenna and old coax on the ground I noticed a mashed place on the coax....not enough for a short but definitely a change in the resistance of the coax. Antenna looked ok so I had the climber replace the new antenna he just put up with the old.
Over the years FR24 has had two vendors for their antenna. One had an open connection where you attached the N Connector and you had to weather seal and another had a built-in shroud that covered the connection. Both antennas are good performers but from a reliability standpoint the one with the shroud weather seals better so even a novice can make a weathertite connection. After 3 typhoons in 2 years the connection on the shrouded antenna didn't show the tell tale signs of water and corrosion.
Comment
-
Your map looked fine. at the bottom if you change the 30,000 to 40,000 notice how your range pattern increases all the way from Zamboanga and Davao.
On your FIBR modem you can do more like port forwarding. I can help you with that.Last edited by paradiselost; 2019-01-03, 06:20.
Comment
-
Originally posted by paradiselost View PostThe mast is 1.5 inch GI. I am going to guess it is up 10 meters because my cables are 10 mtrs long and the receivers are mounted under a shelter out of the weather. I have the power going through a light switch which i use to reset the receivers if necessary. Other than that power is supplied to the two receivers 24/7. The FR24 and the PlaneFinder receivers are out there. The FlightAware RPI is mounted in a box above my desk.
In over 2 years the only problem I have encountered is AC adapters sometime fail from thermal or other causes. Each time FR24 Support supplied replacements when I couldn't get them off the shelf locally. From January of last year I began noticing reduced range for the FR24 receiver until the range dropped down to 50 miles. Suspecting either antenna or coax problems FR24 shipped a replacement set. It took a long time to arrange for climbers but when we replaced the antenna and coax normal range continued. With the antenna and old coax on the ground I noticed a mashed place on the coax....not enough for a short but definitely a change in the resistance of the coax. Antenna looked ok so I had the climber replace the new antenna he just put up with the old.
Over the years FR24 has had two vendors for their antenna. One had an open connection where you attached the N Connector and you had to weather seal and another had a built-in shroud that covered the connection. Both antennas are good performers but from a reliability standpoint the one with the shroud weather seals better so even a novice can make a weathertite connection. After 3 typhoons in 2 years the connection on the shrouded antenna didn't show the tell tale signs of water and corrosion.
I have lots of rtl dongles on hand and sometimes I listen to naia tower/atis/ground control although sometimes signal is very weak. Again I need to put my vhf antenna outside.
Currently I'm averaging around 480 planes a day and a maximum range of 220nm. Definitely I might get better results if I put my coco outside. There are 2 cellsites nearby one of them is around 500meters and the other one is 1.3km. Purchasing a filter or a lna or both might get me better results but are expensive.
Anyway my first problem is still the mast and I need to convince my wife to agree to put a pipe again outside.
Comment
-
Originally posted by hacker.ph View PostThanks for the info. That's what I have in mind for my next upgrade. 1.5 gi the default I think is 6meters in our local hardware.
Currently I'm averaging around 480 planes a day and a maximum range of 220nm. Definitely I might get better results if I put my coco outside. There are 2 cellsites nearby one of them is around 500meters and the other one is 1.3km. Purchasing a filter or a lna or both might get me better results but are expensive.
Talking about interference from cell towers, one of the sites I admin is built on a clift and a cell tower is down the mountain so its radiating elements are within 50 mtrs of the FlightAware RPI receiver's antenna. Not a bit of interference because the RPI has a robust notch filter system tuned to 1090. In my early days with dongles I bought 2 interference filters...it was a waste of money and the insertion loss reduced the number of aircraft being tracked.
On sourcing the the GI pipe, I've found better pricing buying at construction materials outlets. Remember to also get a cap to prevent the mast from filling up with water. Water inside a GI pipe is like a cancer that will rob its strength over time by rusting out. With a multitude of at least #16 guywires it will keep your mast from falling into power lines or your house.
Put your antenna high enough to be able to look over green leaved trees and near-by multi-story buildings.
Comment
-
Hi John, The whole PLDT router is idiosyncratic but thanks for the enlightenment about the LAN ports not speaking to each other. I just wish I could get into the software.
In fact when they were building my house they put CAT5E cables from the sala to the bedroom so I am running a BT Homehub5 from LAN1 as an AP and gigaswitch upstairs where my gear is so they are talking through the HH5. The only other thing on the PLDT LAN is the TV so I havn't faced that problem.
Any clues you can give about admin log in to the fibr router are welcome. I've tried everything I've seen onlin but they seem to have closed all the doors.
Comment
-
Originally posted by Malcolml View PostHi John, The whole PLDT router is idiosyncratic but thanks for the enlightenment about the LAN ports not speaking to each other. I just wish I could get into the software.
In fact when they were building my house they put CAT5E cables from the sala to the bedroom so I am running a BT Homehub5 from LAN1 as an AP and gigaswitch upstairs where my gear is so they are talking through the HH5. The only other thing on the PLDT LAN is the TV so I havn't faced that problem.
Any clues you can give about admin log in to the fibr router are welcome. I've tried everything I've seen onlin but they seem to have closed all the doors.
Sometimes stuff works and then it doesn't.
Comment
-
FR24 Receivers Working and Non-Working 1-4-2019
Working FR24 receivers 1-4-2019 in the Philippines
RADAR F-RPMO1 West Coast of Leyte, Ormoc
RADAR F-RPVA1 East Coast of Leyte, Tacloban
RADAR F-RPVB1 Northern Negros Occidental, Bacolod-Silay
RADAR F-RPVS1 San Jose, Antique, Pinay Island
RADAR F-RPUW1 Marinduque Airport, Marinduque Island
RADAR F-RPLB1 Subic Bay International Airport, Zambales, Luzon Island
RADAR F-RPWC1 Awang Airport, Cotabato
RADAR F-RPVR1 Roxas Airport (RXS) located in Roxas, Capiz, Panay Island
RADAR F-RPLL2 Cavite City, Cavite, Manila Suburb, Luzon Island
RADAR F-RPLL5 Imus City, Cavite, Luzon Island
RADAR F-RPUN1 AND RPUN2, Naga, Camarines Sur
RADAR F-RPUS1 San Fernando, La Union, Luzon
RADAR T-RPMD1 Davao City, Davao City, Davao del Sur, Mindanao
RADAR F-RPMO1 Ozamiz City, Misamis Occidental, Mindanao
RADAR F-RPML3 Cagayan De Oro City-Laguindingan, Misamis Oriental, Mindanao
RADAR F-RPVI1 Iloilo, Cabatuan, Panay Island
RADAR F-RPWE1 Butuan City, Agusan Del Norte, Mindanao
RADAR F-RPVK1 Kalibo, Aklan, Panay Island
RADAR F-RPVK2 Kalibo, Aklan, Panay Island
RADAR F-RPLP1 Legazpi City, Albay, Bicol island
RADAR F-RPVM3 Lahug, Cebu
Missing in Action
RADAR F-RPMZ2 Zamboanga, Zamboanga del Sur, Mindanao
RADAR F-RPMG1 Dipolog, Zamboanga Del Norte, Mindanao
RADAR F-RPMI1 Iligan City, Lanao del Norte, Mindanao
RADAR F-RPMD1 and 2 Davao City, Davao City, Davao del Sur, Mindano
RADAR F-RPVT1 Tagbilaran, Bohol
RADAR F-RPLC1 AND 2 Angeles City, Pampanga, Luzon
RADAR F-RPUB1 Baguio, Benguet, Luzon
RADAR F-RPUT1 Tuguegarao, Cagayan, Luzon
RADAR F-RPLI1 Laoag, Ilocos Norte, Luzon
RADAR F-RPVP1 Puerto Princesa, Palawan Island
paradiselost
Comment
-
Originally posted by Malcolml View PostHi John, The whole PLDT router is idiosyncratic but thanks for the enlightenment about the LAN ports not speaking to each other. I just wish I could get into the software.
In fact when they were building my house they put CAT5E cables from the sala to the bedroom so I am running a BT Homehub5 from LAN1 as an AP and gigaswitch upstairs where my gear is so they are talking through the HH5. The only other thing on the PLDT LAN is the TV so I havn't faced that problem.
Any clues you can give about admin log in to the fibr router are welcome. I've tried everything I've seen onlin but they seem to have closed all the doors.
rpi -> router(vpn client) -> lte modem -> server(vpn gateway)
sample setup: https://dump1090.hacker.ph/
Comment
-
Originally posted by paradiselost View PostTalking about interference from cell towers, one of the sites I admin is built on a clift and a cell tower is down the mountain so its radiating elements are within 50 mtrs of the FlightAware RPI receiver's antenna. Not a bit of interference because the RPI has a robust notch filter system tuned to 1090. In my early days with dongles I bought 2 interference filters...it was a waste of money and the insertion loss reduced the number of aircraft being tracked.
Comment
-
Originally posted by hacker.ph View PostOn our old house before we had a PLDT DSL and have full access to the router. Recently when they rolled out the Fibre plans they've changed the router and blocked all access to it. This prevents people from using port forwarding or self hosting configurations (since Fiber is fast they don't want to use their network for that unless your on a business plan).
On my FIBR modem before they upgraded the firmware knowing the pages where you can set things you could get into the modem and I set my Port Forwarding then for 5 or 6 ports I use with VirtualRadar. Their upgrade didn't bother what I had set. I've had FIBR since January last year. I upgraded from Globe 5mbs DSL and as a promotion for doing that they doubled the 50 mbs plan to 100 mbs for 6 months. Even though the FIBR box across the street was up in November it took about a month for them to commission it and schedule my installation.
I have another Globe 5 mbs dsl plan here in the house running a BPO, I am considering a faster plan since Globe has dropped the 3 year termination agreement.
In this market Globe couldn't give away DSL in competition with FIBR.
From what I have read, if you need to get into the modem, tech support can give you access. Don't expect help in making it work when changing over from DSL because the contract installers just know connecting FIBR and nothing about your setup....that is on you and Google. All of the ADSB receivers use very little data so speed is not a problem.
paradiselost....or...John
Comment
Comment