Announcement

Collapse
No announcement yet.

Uploading with Planeplotter and ground traffic

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Charky
    replied
    Originally posted by Mike View Post
    I would prefer if you only upload with one software, and fr24feed is prefered. There may be interference if you use different softwares together. As I wrote fr24feed works and uploads your ground traffic. It's only temporarily blocked on the webpage right now due too some technical issues. Fr24feed ground traffic should be visible on monday-tuesday again.
    No problem.
    Im uploading to FR24 currently using the fr24feed tool (2 pc's, 2 receiver, 2 antennas etc.). At the same time Im using PP to upload to planefinder to see the difference.
    I can try to contact LSGG4/T-LSGG2.
    btw: why this call changes of the uploaders. bringing a lot of confusion f.ex. in the chat.

    Leave a comment:


  • Mike
    replied
    Originally posted by Charky View Post
    @Mike
    the setup is currently as follows:
    LSGG4/T-LSGG2 is uploading now via PP as Net1 and under T-LSGG2
    T-LSGG1 as usual, and usually no ground traffic
    to allow you to compare my data visually Im uploading as T-EDFY to FR24 and additionally to Planefinder, same receiver, same antenna, both via PP and groundtraffic at LSGG should be shown.
    good luck in searching.
    Karl
    I would prefer if you only upload with one software, and fr24feed is prefered. There may be interference if you use different softwares together. As I wrote fr24feed works and uploads your ground traffic. It's only temporarily blocked on the webpage right now due too some technical issues. Fr24feed ground traffic should be visible on monday-tuesday again.

    Leave a comment:


  • ( EGSS1) Gordon
    replied
    I too have noticed this, I used to getplanes taxiing at EGSS on FR24 when secondary sharing was selected in PP secondary sharing, but since the last update this does not happen now.

    Leave a comment:


  • Charky
    replied
    Originally posted by airport View Post
    I had the same problem with Beast and PP some months ago. I fixed it by setting my PC clock accurate on time.
    thank you, but the time is set hourly.
    the problem here is not the time, problem here is no planes on ground.

    @Mike
    the setup is currently as follows:
    LSGG4/T-LSGG2 is uploading now via PP as Net1 and under T-LSGG2
    T-LSGG1 as usual, and usually no ground traffic
    to allow you to compare my data visually Im uploading as T-EDFY to FR24 and additionally to Planefinder, same receiver, same antenna, both via PP and groundtraffic at LSGG should be shown.
    good luck in searching.
    Karl

    Leave a comment:


  • airport
    replied
    I had the same problem with Beast and PP some months ago. I fixed it by setting my PC clock accurate on time.

    Leave a comment:


  • Mike
    replied
    Originally posted by Charky View Post
    groundtraffic should come via Net1 or EDFY. we tested LSGG4/T-LSGG2. he gets the planes only at a small part at the beginning of the runway, but no taxiing.
    Can I stop T-EDFY1 because there is no change ?
    Yes I can see YELLOW1 coming from T-EDFY1 now. I think that ground traffic from T- feeders is temporarily blocked on the webpage right now as there is some kind of issue with data getting mixed up from T-feeders.

    Leave a comment:


  • Charky
    replied
    groundtraffic should come via Net1 or EDFY. we tested LSGG4/T-LSGG2. he gets the planes only at a small part at the beginning of the runway, but no taxiing.
    Can I stop T-EDFY1 because there is no change ?

    Leave a comment:


  • Mike
    replied
    Originally posted by Anmer View Post
    Sure Mike, it's your call. But you do promote feeding via PP as well as your own client software.
    The new software is still in late beta stage, as soon as we are satisfied with how it works, and we have created a form where feeders can create they key by themselves, the PP option will be removed.

    Originally posted by Charky View Post
    ok, so what I can do is setup tomorrow as a test my german upload (ED??) here with the beast and PP.
    Never mind, this change must have happened during this week. 2 or 3 days ago it was running fine and there was no update on my side (beside this evening the PP update).
    But, what I dont like with the new upload is, that FR24 can specify the upload frequence.
    That might bring some uploaders with a maximum upload contingent per month or day in trouble. And if they find out its too late or will cost a lot of money.


    Couldnt wait. set it up now
    EDxx and NET1 are running now at the same (directional) antenna and the beast. The FR24feed is running with udp and GND and ModeS = Yes
    LSGG1 is running with sbs1er antenna at the roof omnidirectional with tcp and GND and ModeS yes


    but still no ground traffic like I see at the PP screen.
    The upload interval is lower but the data transfer should be lower as the data is more compressed. If someone want it higher we can adjust that.
    I can see that there is ground traffic from T-LSGG2 uploaded but I can't see any from T-LSGG1.

    Leave a comment:


  • Charky
    replied
    ok, so what I can do is setup tomorrow as a test my german upload (ED??) here with the beast and PP.
    Never mind, this change must have happened during this week. 2 or 3 days ago it was running fine and there was no update on my side (beside this evening the PP update).
    But, what I dont like with the new upload is, that FR24 can specify the upload frequence.
    That might bring some uploaders with a maximum upload contingent per month or day in trouble. And if they find out its too late or will cost a lot of money.


    Couldnt wait. set it up now
    EDxx and NET1 are running now at the same (directional) antenna and the beast. The FR24feed is running with udp and GND and ModeS = Yes
    LSGG1 is running with sbs1er antenna at the roof omnidirectional with tcp and GND and ModeS yes


    but still no ground traffic like I see at the PP screen.
    Last edited by Charky; 2012-04-27, 16:54.

    Leave a comment:


  • Anmer
    replied
    Sure Mike, it's your call. But you do promote feeding via PP as well as your own client software.

    Leave a comment:


  • Mike
    replied
    Originally posted by Anmer View Post
    Surely if FR24 isn't handling ground traffic from the PP feed and Planefinder does, isn't fixing that a better solution?
    Of course it is, if you know what is wrong. We have PP feeders uploading ground traffic, so it's not a general problem.


    The reason why we have put hundreds of hours on an own software is to have control of the upload process. Now we can control what is upload and how. So of course we would prefer if the feeders use the new software, instead in finding problems with a software we don't have control over.

    Leave a comment:


  • Anmer
    replied
    Surely if FR24 isn't handling ground traffic from the PP feed and Planefinder does, isn't fixing that a better solution?

    Leave a comment:


  • Mike
    replied
    Originally posted by Charky View Post
    @Mike
    Im using the Beast with PP. So need to think about how I could get it running. Might take some time. I dont like to play around with usb or serial splitters.
    You can just run Fr24feed on top of that, you don't need any splitters.

    Leave a comment:


  • Charky
    replied
    ok, Im now switching back to FR24 to let them find out what they have done.

    Leave a comment:


  • Anmer
    replied
    Thanks for trying the "other" sharing website.

    I upload to FR24 via another sharing network and the software didn't show on-ground traffic. We now know it's not a PP issue.

    Leave a comment:

Working...
X