Announcement

Collapse
No announcement yet.

Help Setting Up Flightradar24 Software

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • wildthing01
    replied
    Many thanks to all here in the forum.

    Now my Raspberry is feeding.

    Leave a comment:


  • wiedehopf
    replied
    Don't type start, type restart!

    sudo systemctl restart fr24feed

    Anyway you can also reboot the RPi.

    Also consider upgrading dump1090, fr24 is by default using a very old version.
    https://github.com/wiedehopf/adsb-sc...for-dump1090fa

    Leave a comment:


  • wildthing01
    replied
    Hello,

    The feeding software now seems to be fully configured
    Except for a few minor misunderstandings.
    How do I get the software to feed.
    with the command:
    sudo service fr24feed start
    Do not start feeding?
    Can someone help me please? or is it enough if I restart the Raspberry?

    Many thanks in advance for your reply

    Leave a comment:


  • wiedehopf
    replied
    Leave the prompt for the sharing key empty.

    You will then get a new sharing key.
    Old sharing keys often cause problems.

    Leave a comment:


  • wildthing01
    replied
    The system tells me that my email address is wrong. Earlier on the Windows feeding software I logged in with the same email address.
    What am I doing wrong?
    I'm sorry for the questions to the forum.
    20190902_142915.jpg

    Leave a comment:


  • wiedehopf
    replied
    After running the signup, you'll need to restart fr24:

    sudo systemctl restart fr24feed

    I suspect you'll have to look up how to use putty/ssh, it is described here:
    https://forum.flightradar24.com/thre...l=1#post121506
    Last edited by wiedehopf; 2019-09-02, 11:35.

    Leave a comment:


  • Oblivian
    replied
    Originally posted by wildthing01 View Post
    Hello everybody,

    many thanks for the help. I downloaded the software from Fligthradar24. The feeding software seems to work, but the software does not feed the data into the internet
    My question: What am I doing wrong? Are the parameters / entries not entered correctly? (see attached photo)
    What am I doing wrong. Can someone help me get the feeding software to work?

    Best regards
    Nils[ATTACH=CONFIG]11046[/ATTACH]
    Does not appear so

    sudo fr24feed --signup

    Re-enter same details as before.

    Leave a comment:


  • wildthing01
    replied
    Hello everybody,

    many thanks for the help. I downloaded the software from Fligthradar24. The feeding software seems to work, but the software does not feed the data into the internet
    My question: What am I doing wrong? Are the parameters / entries not entered correctly? (see attached photo)
    What am I doing wrong. Can someone help me get the feeding software to work?

    Best regards
    Nils20190902_124637.jpg

    Leave a comment:


  • abcd567
    replied
    wildthing01:

    Which OS you have installed?

    PI24 image downloaded from https://www.flightradar24.com/build-your-own

    OR

    Raspbian image downloaded from https://www.raspberrypi.org/downloads/raspbian/

    Leave a comment:


  • wildthing01
    replied
    Hello everybody,

    I've tried so hard to set up the FR24 software for feeding, but I can not get it to work. Can someone help me with the installation of the FR24 software on my Rasberry Pi 2? The software I have already copied to an SD card and the software also starts. The DVBT stick is also recognized. I do not know where to enter my access data?

    Many Thanks
    Nils

    Leave a comment:


  • abcd567
    replied
    flyingLunchbox:

    To reconfigure only
    Code:
    fr24feed --reconfigure
    To signup and reconfigure
    Code:
    fr24feed --signup
    Last edited by abcd567; 2019-07-17, 22:24.

    Leave a comment:


  • flyingLunchbox
    replied
    how can i restart the setup wizard ?

    Leave a comment:


  • ShoeGolf
    replied
    I have to admit my hardest time was ssh into the Pi shell. I cannot express how important to type exactly and watch your spaces

    Leave a comment:


  • kaninmike
    replied
    Originally posted by k9act View Post
    Problem solved.

    As per Nisbo's posting on the PP thread I changed the following:

    In set up I said no to the questions about raw data and base station.

    I added --net to the dump1090 arguments

    In ADSBscope I choose Port 30002 for RDC (nothing new there)
    and what made it work was selection Beast as the decoder instead of the obvious dongal choice.

    I have no idea what any of this means or why it now works but I am probably too old to learn.

    Thanks for the help,

    Jack
    --net that worked for me too, Thanks alot !!!

    Leave a comment:


  • Oblivian
    replied
    And no sooner to I say that..

    http://forum.flightradar24.com/threa...8021#post68021

    Leave a comment:

Working...
X