I'm using a Flightaware USB Pro Stick plus (Blue) and flight aware 1090MHz ads-b antenna. I have followed instructions on most of the posts on this forum regarding feeding data to multiple sites. I have tried the following,
1.On a fresh Fresh Raspbian buster Image, by running,
I get the following error,
It says 0 upgraded, 0 newly installed, 0 to remove and 14 not upgraded because I had already tried it once and an older version is installed (not using the bash script though). But, this error was occuring on a fresh Raspbian image. Mainly,
2. Tried installing fr24 on PiAware image. I get the same error, can't even go to the sign-up process!
3. Tried to install PiAware on a FR24 image. With dump1090-fa and dump1090-mutability enabled flight aware gets MLAT but FR24 does not enable MLAT. After removing dump1090-mutability, i observe the same behaviour as mentioned in the previous sentence. With dump1090-fa removed and dump1090-mutability installed, flightaware does not get MLAT, but FR24 does work fine.
4.Tried everything mentioned in point 3 with receiver changed to Mode-S Beast(TCP) instead of "dvbt" in FR24feeder config file which looks something like this,
with the above config file suggested on these forums (to feed piaware and fr24), FR24 also does not run with MLAT enabled or does not upload anything.
With the below config file,FR24 runs with MLAT enabled and works fine.
The fact that,
is giving an error as shown above in this post is what is preventing me from following most guides on this forum to go about uploading data to FR24 and FlightAware!
How do I go about solving this issue? Any suggestions are very much appreciated! Thanks in advance!
1.On a fresh Fresh Raspbian buster Image, by running,
Code:
sudo bash -c "$(wget -O - http://repo.feed.flightradar24.com/install_fr24_rpi.sh)"
Code:
pi@raspberrypi:~ $ sudo bash -c "$(wget -O - http://repo.feed.flightradar24.com/ install_fr24_rpi.sh)" --2020-04-22 17:01:28-- http://repo.feed.flightradar24.com/install_fr24_rpi.sh Resolving repo.feed.flightradar24.com (repo.feed.flightradar24.com)... 52.216.232.213 Connecting to repo.feed.flightradar24.com (repo.feed.flightradar24.com)|52.216.232.213|:80.. . connected. HTTP request sent, awaiting response... 200 OK Length: 1284 (1.3K) [text/x-sh] Saving to: ‘STDOUT’ - 100%[================================================== ================================================== ================================================== =============>] 1.25K --.-KB/s in 0.001s 2020-04-22 17:01:33 (1.95 MB/s) - written to stdout [1284/1284] Hit:1 http://archive.raspberrypi.org/debian buster InRelease Hit:2 http://flightaware.com/adsb/piaware/files/packages buster InRelease Hit:3 http://repo.feed.flightradar24.com flightradar24 InRelease Hit:4 http://raspbian.raspberrypi.org/raspbian buster InRelease Reading package lists... Done Reading package lists... Done Building dependency tree Reading state information... Done dirmngr is already the newest version (2.2.12-1+rpi1+deb10u1). The following package was automatically installed and is no longer required: libbladerf1 Use 'sudo apt autoremove' to remove it. 0 upgraded, 0 newly installed, 0 to remove and 14 not upgraded. Executing: /tmp/apt-key-gpghome.qZI2Q66W6d/gpg.1.sh --recv-key --keyserver pool.sks-keyservers.net C969F07840C430F5 gpg: keyserver receive failed: Server indicated a failure Executing: /tmp/apt-key-gpghome.wk5KGDA5zD/gpg.1.sh --recv-key --keyserver pgp.mit.edu C969F07840C430F5 gpg: keyserver receive failed: Server indicated a failure
Code:
Executing: /tmp/apt-key-gpghome.qZI2Q66W6d/gpg.1.sh --recv-key --keyserver pool.sks-keyservers.net C969F07840C430F5 gpg: keyserver receive failed: Server indicated a failure Executing: /tmp/apt-key-gpghome.wk5KGDA5zD/gpg.1.sh --recv-key --keyserver pgp.mit.edu C969F07840C430F5 gpg: keyserver receive failed: Server indicated a failure
3. Tried to install PiAware on a FR24 image. With dump1090-fa and dump1090-mutability enabled flight aware gets MLAT but FR24 does not enable MLAT. After removing dump1090-mutability, i observe the same behaviour as mentioned in the previous sentence. With dump1090-fa removed and dump1090-mutability installed, flightaware does not get MLAT, but FR24 does work fine.
4.Tried everything mentioned in point 3 with receiver changed to Mode-S Beast(TCP) instead of "dvbt" in FR24feeder config file which looks something like this,
Code:
bs="no" raw="no" mlat="yes" mlat-without-gps="yes" logmode="0" receiver="beast-tcp" host="127.0.0.1:30005" procargs="--gain -10" fr24key="xxxxxxxxxxxxxx"
With the below config file,FR24 runs with MLAT enabled and works fine.
Code:
bs=yes raw=yes mlat="yes" mlat-without-gps="yes" logmode="0" procargs="--gain -10" fr24key=xxxxxxxxxxxxx receiver="dvbt"
Code:
sudo bash -c "$(wget -O - http://repo.feed.flightradar24.com/install_fr24_rpi.sh)"
How do I go about solving this issue? Any suggestions are very much appreciated! Thanks in advance!
Comment