Announcement

Collapse
No announcement yet.

Windows Setup/Feed Migration (virtualVM) Assistance

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Oldertarl
    replied
    Alright all clear
    placed --fix back in the options
    now project "bring the antenna outside" has to start as the 50nM is just not doing the trick for me

    Leave a comment:


  • abcd567
    replied
    Originally posted by Oldertarl View Post
    Is there a special reason this is set to --fix rather than adding the lat and lon that I am missing in oversight?
    The receiver location is determined by adding arguments --lat xxxx --lon yyyy.

    The parameter --fix has nothing to do with the location of receiver. ​​​​It does error correction on some messages which have been damaged by noise in transit, which would otherwise be discarded. The downside of this is that it increases the chances that badly damaged messages could be wrongly “corrected”, producing bad data.

    Usually these bad messages are then filtered out by subsequent processing (this is where the “single tracks” statistic comes from).


    Leave a comment:


  • Oldertarl
    replied

    When looking at graphs1090 the range is not showing any data
    Browsing the forums I found that the location is required in dump1090
    When adding the location in DECODER_OPTIONS="--max-range 360 --lat 50.0 --lon 6.0" , removing the --fix
    The service restarts without issues and shows the range data in the graphs
    Is there a special reason this is set to --fix rather than adding the lat and lon that I am missing in oversight?

    Leave a comment:


  • Oldertarl
    replied
    Was away for the weekend, but was able to install the correct linux version for the listed scripts
    Also installed the fr24feed and dump1090-fa, including graphs1090 with all options I hade before
    I am a very happy man as we speak!

    Almost coming to my last topic on my list for this first feeder, getting the antenna to the best possible position, as 50nM is just poor knowing where I live (north of Luxembourg)

    Thanks a million for the assistance !

    Leave a comment:


  • abcd567
    replied

    Oldertarl:

    STEP-1:
    Remove amd64 package and binary

    Code:
    sudo rm /usr/share/fr24/fr24feed_1.0.24-5_amd64.tgz  
    
    sudo rm -rf /usr/share/fr24/fr24feed_amd64  
    
    sudo rm /usr/bin/fr24feed

    STEP-2:
    Download, extract, and copy to folder /usr/bin/ the i386 binary

    Code:
    sudo wget -O /usr/share/fr24/fr24feed_1.0.25-3_i386.tgz "https://repo-feed.flightradar24.com/linux_x86_binaries/fr24feed_1.0.25-3_i386.tgz"  
    
    sudo tar xvzf /usr/share/fr24/fr24feed_1.0.25-3_i386.tgz -C /usr/share/fr24  
    
    ​​​​sudo cp /usr/share/fr24/fr24feed_i386/fr24feed /usr/bin/
    Restart fr24feed
    Code:
    sudo systemctl restart fr24feed

    .
    Last edited by abcd567; 2020-08-15, 11:20.

    Leave a comment:


  • Oldertarl
    replied
    I guess the mismatch break the code.
    Now I am not at all familiar with the difference between amd64 and i386
    is that to be corrected on the linux build or in the way to install it fr24feed?

    Code:
    pi@FlightHost:~$ dpkg --print-architecture
    i386
    pi@FlightHost:~$ ls /usr/share/fr24
    fr24feed_1.0.24-5_amd64.tgz fr24feed_amd64
    pi@FlightHost:~$ ls /usr/bin/fr24feed
    /usr/bin/fr24feed
    pi@FlightHost:~$
    EDIT
    2.1.2. CPU Support
    Both AMD64 and Intel 64 processors are supported.

    They clearly got me on the wrong foot
    Starting from scratch ;-)
    Last edited by Oldertarl; 2020-08-15, 10:01.

    Leave a comment:


  • abcd567
    replied
    Sems linux binary "fr24feed" is missing.or corrupted, or mismatching with you machines architecture.

    Either
    (1) the tarball "fr24feed_1.0.24-5_amd64.tgz" did not get downloaded

    OR
    (2) the tarball downloaded, but extrsction of binary "fr24feed" failed

    OR
    (3) the linux binary "fr24feed" did not get copied to folder /usr/bin/


    Please post output of following cimmands to reveal what is missing

    Check binary
    Code:
    ls /usr/share/fr24  
    
    ls /usr/bin/fr24feed

    Check architecture of you machine/os
    Code:
    dpkg --print-architecture  
    
    dpkg --print-foreign-architectures
    Last edited by abcd567; 2020-08-15, 07:23.

    Leave a comment:


  • wiedehopf
    replied
    You got the wrong binary for your architecture.

    Leave a comment:


  • Oldertarl
    replied
    Code:
    -bash: /usr/bin/fr24feed: cannot execute binary file: Exec format error
    and I am running dump1090-fa only
    installed with (3) For Debian 9 & 10 and Ubuntu 18 & 19 (dump1090-fa)
    sudo bash -c "$(wget -O - https://raw.githubusercontent.com/abcd567a/fr24feed-debian-ubuntu-amd64/master/install-dump1090-fa.sh)"

    Not sure if it matters, but when runing fr24feed with sudo I get the below
    Code:
    pi@FlightHost:~$ sudo fr24feed
    /usr/bin/fr24feed: 1: /usr/bin/fr24feed: Syntax error: "(" unexpected

    Leave a comment:


  • abcd567
    replied
    Which decoder (dump1090-mutability / dump1090-fa) you have installed?

    Please post the output of following command

    Code:
    fr24feed

    Leave a comment:


  • Oldertarl
    replied
    Running into a strange problem

    As my pi was constant at high CPU I decided to follow the instruction on https://github.com/abcd567a/fr24feed...ster/README.md
    Run all the code and included the key in the ini as instructed on a 'old' desktop running a clean install of
    PRETTY_NAME="Debian GNU/Linux 10 (buster)"
    NAME="Debian GNU/Linux"
    VERSION_ID="10"
    VERSION="10 (buster)"

    Code:
    receiver="beast-tcp"
    host="127.0.0.1:30005"
    fr24key="<removed>"
    
    bs="no"
    raw="no"
    logmode="1"
    logpath="/var/log/fr24feed/"
    windowmode="0"
    mpx="no"
    mlat="no"
    mlat-without-gps="no"
    use-http=yes
    http-timeout=20
    Code:
    ● fr24feed.service - Flightradar24 Feeder
    Loaded: loaded (/lib/systemd/system/fr24feed.service; enabled; vendor preset: enabled)
    Active: failed (Result: exit-code) since Fri 2020-08-14 23:42:47 CEST; 25s ago
    Process: 758 ExecStartPre=/bin/mkdir -p /var/log/fr24feed (code=exited, status=0/SUCCESS)
    Process: 759 ExecStartPre=/bin/chown fr24 /var/log/fr24feed (code=exited, status=0/SUCCESS)
    Process: 760 ExecStart=/usr/bin/fr24feed (code=exited, status=203/EXEC)
    Main PID: 760 (code=exited, status=203/EXEC)
    
    Aug 14 23:42:47 FlightHost systemd[1]: fr24feed.service: Service RestartSec=100ms expired, scheduling restart.
    Aug 14 23:42:47 FlightHost systemd[1]: fr24feed.service: Scheduled restart job, restart counter is at 5.
    Aug 14 23:42:47 FlightHost systemd[1]: Stopped Flightradar24 Feeder.
    Aug 14 23:42:47 FlightHost systemd[1]: fr24feed.service: Start request repeated too quickly.
    Aug 14 23:42:47 FlightHost systemd[1]: fr24feed.service: Failed with result 'exit-code'.
    Aug 14 23:42:47 FlightHost systemd[1]: Failed to start Flightradar24 Feeder.
    have tried the hint to comment out the user fr24 to run as root - but also without any luck

    Not being a linux guru - did some decent seeking around but, have not been able to find the solution
    There is a lot of talk when searching about adding #!/bin/bash at the top of the .service file
    but as said, not confident enough if that is the right way to go.

    Any help would be appreciated

    Last edited by Oldertarl; 2020-08-14, 22:16.

    Leave a comment:


  • abcd567
    replied
    Originally posted by arash View Post
    I found this guide but I Don't know how to use it!

    https://forum.flightradar24.com/foru...A-Brief-Guide=
    This guide is fo Raspberry Pi (armv7 / armv8). It does not apply to VM on Windows which runs on x86_x64 or i386, or i686 machines.


    Originally posted by arash View Post
    Dear All

    Is it possible to feed date to multiple sites with windows & VM configuration?

    for example feed flightware or radarbox24 with flightradar 24?
    • dump1090-fa: yes, but you will havd to build it from source code.
    • dump1090-mutability: on debian buster, can be installed by "sudo apt-get install dump1090-mutability". On other distros like ubuntu etc, you will have to build it from source code.
    • fr24feed: binary avaiable, you have to create necessary config & service files yourself, (Click here)
    • piaware: you have to build it from source code
    • rb24feed: no, they dont have feeder for x86_x64 or i386. They have only for Pi (armv7 / armv8)

    Leave a comment:


  • arash
    replied
    Dear All

    Is it possible to feed date to multiple sites with windows & VM configuration?

    for example feed flightware or radarbox24 with flightradar 24?

    I found this guide but I Don't know how to use it!

    https://forum.flightradar24.com/foru...A-Brief-Guide=

    Leave a comment:


  • tanhy
    replied
    Do I need the Oracle VM VirtualBox Extension Pack and PuTTY if I am connecting to Basestation via network?
    Last edited by tanhy; 2019-07-27, 20:36.

    Leave a comment:


  • Oblivian
    replied
    Originally posted by wiedehopf View Post

    Edit: I'll just leave my post here in case he checks this thread instead of the one you moved his post to Oblivian.
    I don't think there is any notification on this forum so people don't find the answers to their own posts.
    There is, but the number of times I've seen disposable EMails used (and unsure if moderated and later approved like this was send them) some users aren't helping themselves

    Leave a comment:

Working...
X