Feed options for depreciated windows feeder

[abcd567]

@Tritium

Did you write "DietPi_NativePC-BIOS-x86_64-Bullseye" on SD card and tried to boot Thin Client from SD card? The above noted OS is bases on Debian 11.3 Bullseye, which is compatible to Pentium (I586)

DietPi installation on microSD card - for HP T520 units without on-board SSD

.

[abcd567]

@awkward

Good news. Your Dongle is OK and accessible by Linux OS.

Seems after installing dump1090-mutability, you did not issue one or both following TWO very essential commands,
or maybe you did issue these commands, but for some reason they did not go through.

Please issue following commands again, and after REBOOT, check the map (locahost/dump1090/gmap.html) and after 5 minutes, fr24 status (sudo fr24feed-status)

sudo usermod -a -G plugdev dump1090  

sudo reboot

[awkward]

This is what I'm getting:

5.jpg

[abcd567]

@awkward

Issue following 3 commands.
What is output of the last command below?

​​​​​sudo apt install rtl-sdr  

sudo systemctl stop dump1090-mutability  

rtl_test -t

.

[awkward]

Thanks for taking the time helping me with this.

On localhost/dump1090/gmap.html I'm getting this:

3.jpg

This is what I'm getting running that command:

4.jpg

[abcd567]

@awkward
I assume that you have installed dump-1090-mutability. If I am right, then:

(1) The screenshots you posted shows in your browser you can see settings page at "localhost:8754/settings.html". In the same browser, do you see a map with aircraft at "localhost/dump1090/gmap.html" ?

(2) Please post out out of following command:

 
sudo systemctl status dump1090-mutability  

​​​​​

[awkward]

Hey guys! I'm a bit stuck and don't know what I'm doing wrong. I followed the tutorial in the first post, installed dump1090, but I don't know where to take it from here... Does anyone have any suggestions? Thank you!


1.jpg

2.jpg

[abcd567]

DietPi installation on microSD card - for HP T520 units without on-board SSD

Installation of OS on 16 GB microSD card


(1) Go to Image download page : https://dietpi.com/

(2) Scroll down till you see following. Click on " Native PC for BIOS/CSM x86_64"

DietPi-Thin-Client-1.png




(3) Download "Direct write Image"
dietpi.com/downloads/images/DietPi_NativePC-BIOS-x86_64-Bullseye.7z



DietPi-Thin-Client-2.png




(4) Use 7zip to extract image

DietPi-Thin-Client-2a.png





(5) Use Raspberry Pi Imager OR Win32 Disk Imager or Balena Etcher to write the extracted image to microSD card

Win32DiskImager
DietPi-Thin-Client-4.png



(6) Plugin the (microSD card+USB Card Reader) into Thin-Client, power on, Esc, F10, and select boot from USB.



DietPi-Thin-Client-5.png


.

[Tritium]

1. I have tried 32bit version.

System requirements to run Slax

Processor:	i686 or newer CPU, all Intel processors and AMD processors will work	An x86_64 CPU, like AMD Athlon 64, Opteron, Sempron, Intel Core 2/i3/i5/i7, and others
Memory:	128 MB of RAM for desktop 512 MB of RAM to run Web browser	128 MB of RAM for desktop 512 MB of RAM to run Web browser

i got the message when booting:

"This kernel requires an i686 CPU, but only detected an i586 CPU"

And it stop booting.

2. Yes I have read everything and did as readme file says. I got the sdcard in usb sdcard reader. I tried it on another machine and it is working, even the usb wifi card is visible and working without any issue.

Thing is the T5710 with Transmeta Crusoe 800 MHz is consuming about 7Watts. It’s good option for 24h feed.

https://www.parkytowers.me.uk/thin/hp/t5710/

[abcd567]

I have encountered a problem. My thin client HP T5710 has i586 cpu, and the Slax is only for i686, so it doesn’t start.

(1) If you tried the 64-bit image, then now try the 32-bit image
https://ftp.sh.cvut.cz/slax/Slax-11....bit-11.3.0.iso


(2) Did you copy-paste folder "slax" from downloaded .iso file to the SD card, or burned the .iso image to SD card?
The instruction page says to copy-paste
https://www.slax.org/starting.php

.

[Tritium]

I have encountered a problem. My thin client HP T5710 has i586 cpu, and the Slax is only for i686, so it doesn’t start.

[abcd567]

OMFG, abcd567 you are the right guy! Thank you very much. I am now downloading the iso.
it would be great if it can run from RAM or from locked SD card.

Go to this page for instructions to install SLAX OS on USB flash Memory Stick (also valid for SD card and microSD card)

https://www.slax.org/starting.php


.

[Tritium]

OMFG, abcd567 you are the right guy! Thank you very much. I am now downloading the iso.
it would be great if it can run from RAM or from locked SD card.

[abcd567]

Tritium

Install SLAX OS (current version based on Debian Bullseye) on your SDcard.
It is designed to be installed on USB flash stick, or microSD card or SDcard.

I have done this on a Thin-Client HPT520 (a low capacity amd64 computer)

https://discussions.flightaware.com/...hobby/82096/32


https://discussions.flightaware.com/...orking/82475/7


Note: Do NOT install FR24 feeder, dump1090 etc as default user root.
Instead create a new user and install using this new user.
For example I created user abcd (you may use any name of your choice)

root@slax:~# adduser abcd

root@slax:~# apt update

root@slax:~# apt install sudo

root@slax:~# usermod -a -G sudo abcd

root@slax:~# groups abcd
abcd : abcd sudo


## Now switched to user abcd,

root@slax:~# su abcd

abcd@slax:/root$ cd

abcd@slax:~$

20220414_072047-R3.jpg




Download Slax : https://www.slax.org/

Slax 64bit	11.3.0	slax-64bit-11.3.0.iso	9d94c1796ba4c79fb05bb9f35c3fe188	277 MB	changelog
Slax 32bit	11.3.0	slax-32bit-11.3.0.iso	042c2154a766bcecbf49d82ec32a658a	273 MB	changelog
Slax iPXE	11.3.0	slax-ipxe.iso	b347608199f2a0a70fb7a31beb460c20	0.88 MB	changelog

Install Slax on USB Flash Memory OR microSD card: https://www.slax.org/starting.php



NOTE:


Current version of SLAX is based on Debian 11.3 Bullseye. It is an excellent lightweight distro, fast boot, which can be run from a USB flash memory or microSD card+USB card reader. By default it runs with persistance, but has option to change to run without persistance or totally from RAM to be selected at boot by pressing Esc button.

It also has a Network Manager icon on Desktop, and by running it, the network (wire/wifi/Bluetooth) can be configured easily, like settings in standard Debian Desktop.



SLAX-1.jpg



SLAX-2.jpg

[Tritium]

Hi there!

My old setup is dead. Because I am not the linux guy, I need some help. I found old HP T5710 with 800MHz processor. It only consume up to 14W, so I’m searching to use it for FR24 feed. Can anybody help me with any information which system I should try to start onto this machine?
The best option would be to run whole thing from SDcard that is read only. It don’t have any hard drive or ssd. I don’t need any log file or something on it too.

Regards!