How to use RTL1090+FR24feed+Planeplotter simultaneously

[riki]

No. length from end to end needs to be 13.7 cm.

Not each leg.

13.7 cm from tip to tip.

Use the shorter parts included which can be screwed in.

Anyway your location is very bad.
Try on the roof

L/4=6.8, L/2=13.6 :-) My location is very shit -) i can't go to the roof, i know about it////

[wiedehopf]

No. length from end to end needs to be 13.7 cm.

Not each leg.

13.7 cm from tip to tip.

Use the shorter parts included which can be screwed in.

Anyway your location is very bad.
Try on the roof

[riki]

scr14.jpg А/С has become 4. made two counterbalances 13,7sm scr15.jpg I have poor antenna placement. 2nd floor, and around the 10 floors concrete houses.
now I see airplanes around 120km
Now you need to solve the problem why virtual radar and fr24feed do not work together.

[riki]

Yeah the cable probably doesn't help either.

It looks like the rtl-sdr blog starter set.

it's better than nothing

[wiedehopf]

Yeah the cable probably doesn't help either.

It looks like the rtl-sdr blog starter set.

[Oblivian]

Your antenna is wrong.

Using such a type of antenna the overall length should be 13.7 cm

If you have the set i believe you have, use the shorter antenna ends and adjust to length from end to end to 13.7 cm.

Hah, I didn't notice that on mobile. Its a pair of rabbit ears! Not only wrong range tuned, but likely rubbish cable to it

[wiedehopf]

Your antenna is wrong.

Using such a type of antenna the overall length should be 13.7 cm

If you have the set i believe you have, use the shorter antenna ends and adjust to length from end to end to 13.7 cm.

[riki]

THR XX db [YY] whats this YY and how mutch be XX for good signal? senks :-))

[Oblivian]

A/C:2

That's very low. The stats page shows you have sen't data. But you need to receive more than that for longer

Maps (VRS) do not always show real lost/bad signal

[riki]

scr13.jpg work :-) but without virtual radar. I want ask, how mutch will be THR db for good receive?

[Oblivian]

ABCD already demonstrated it works fine with default settings.

https://forum.flightradar24.com/threads/11567-How-to-use-RTL1090-FR24feed-Planeplotter-simultaneously?p=116157&viewfull=1#post116157

But then you had 0 signal 0 contacts

And now all of a sudden you do. What did you do to make RTL1090 go from 0 traffic to some?

[riki]

my fr24feed.ini
receiver="avr-tcp"

fr24key=""

host="localhost:31001"

bs="no"

raw="no"

logmode="1"

procargs="--net"

windowmode="1"

mpx="no"

mlat="yes"

mlat-without-gps="yes"

use-http=yes

http-timeout=20

[riki]

I'm so sad scr12.jpg

[riki]

rtl1090 more informative
my antenna scr11.jpg antenna long beams 55sm up and 55sm down scr10.jpg virtual radar receive data and i see fly on the map, but server fr24 not receive this data.

[Oblivian]

Getting a bit over complicated

Why need rtl1090 specifically?

It is only avr if you start RTL with /avr. Should be host 127.0.0.1 , type beast tcp (binary) port 31001

The table is full. So receiving at the stick level OK. But there are no lights on the tcp/UDP connection status in RTL.

https://forum.flightradar24.com/showthread.php?p=75195

Sent from my EML-L09 using Tapatalk