Announcement

Collapse
No announcement yet.

Activating Pi24 error?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Activating Pi24 error?

    I have configured a Pi24 unit and I have received the following e-mail: Thank you for connecting to Flightradar24! We are now receiving and processing live data from your receiver.

    Running "sudo service fr24feed status" I get:

    [ ok ] FR24 Feeder/Decoder Process: running.
    [ ok ] FR24 Stats Timestamp: 2016-07-22 12:18:02.
    [ ok ] FR24 Link: connected [UDP].
    [ ok ] FR24 Radar: T-OMDW6.
    [ ok ] FR24 Tracked AC: 1.
    [ ok ] Receiver: connected (6186 MSGS/0 SYNC).
    [ ok ] FR24 MLAT: ok [UDP].
    [ ok ] FR24 MLAT AC seen: 0.

    But on the "Activate new receiver" webpage I get the error that "No devices found". My Pi24 receiver is in the same network as my web browser.

    Checking the "Share statistics" webpage for the UAE there are only 14 users and my receiver is not listed (even it could be placed last).

    The latest log file reads:

    2016-07-22 12:22:53 | [feed][n]ping 6
    2016-07-22 12:22:54 | [feed][n]syncing stream result: 1
    2016-07-22 12:23:01 | [mlat][i]No ADS-B time reference available (0/0)
    2016-07-22 12:23:08 | [mlat][i]Pinging the server
    2016-07-22 12:23:08 | [mlat][i]Stats 68/0
    2016-07-22 12:23:11 | [mlat][i]No ADS-B time reference available (0/0)

    Any advice? BTW how to I clear the "No ADS-B time reference available" error?

    Thanks in advance.

    #2
    1) Yesterday I burned Pi24 img on my microSD card, and inserted into RPi and powered up. After finishing configuration, when I checked /var/log/fr24feed.log file, I found "No ADS-B time reference available" error. I did not do anything. After few hours when I checked the log file again, this error has disappeared.

    2) Type the following in your browser to see your settings. The first entry on top left is your sharing key. If it is blank, enter the sharing key provided to you by Flightradar24, and click Save and then Restart buttons at bottom right of the page.

    http://xxx.xxx.xx.xx:8754/settings.html (replace xxx.xxx.xx.xx by your RPi's IP address on your local network). See screenshot below:

    Pi24 Settings.png

    You can configure your feed either by above page in browser, or by command line below:
    Code:
    #If sharing key is not already entered & saved
    sudo fr24feed --reconfigure --fr24key=YOUR SHARING KEY
    #Replace "YOUR SHARING KEY" by the actual sharing key provided to you by Flightradar24.
    
    #If sharing key is already entered & saved, but want to change configuration
    sudo fr24feed --reconfigure
    
    #Complete the configuration wizard. 
    #When asked for additioal arguments for dump1090, enter following: 
    
    --net --net-http-port 8080
    
    #After completing configuration, restart the feed
    
    sudo service fr24feed restart
    Last edited by abcd567; 2016-07-22, 14:28.

    Comment


      #3
      Thanks for the advice and I have basically just copied out as in your snapshot:

      1. Receiver was AVT (TCP) changed to DVBT Stick
      2. Process arguments added: --net --net-http-port 8080
      3. RAW data (30002/30334) was "No" changed to "Yes"
      4. Decoded data (30003) was "No" changed to "Yes"

      pi24.jpg

      Comment


        #4
        So now when I checked the status there is an error:

        $ sudo service fr24feed status
        [ ok ] FR24 Feeder/Decoder Process: running.
        [ ok ] FR24 Stats Timestamp:.
        [FAIL] FR24 Link: unknown ... failed!
        [FAIL] Receiver: down ... failed!
        [FAIL] FR24 MLAT: not running ... failed!

        So I ran the reconfigure command via command line. Everything went well until the end where there is this submitting form error now:

        ...
        ...
        Submitting form data...ERROR

        Invalid email provided!

        Would you like to try again?

        Saving settings to /etc/fr24feed.ini...OK
        Settings saved, please run "sudo service fr24feed restart" to use new configuration.

        $ sudo service fr24feed restart
        [ ok ] Stopping FR24 feeder: fr24feed.
        [ ok ] Starting FR24 feeder: fr24feed.

        $ sudo service fr24feed status
        [ ok ] FR24 Feeder/Decoder Process: running.
        [ ok ] FR24 Stats Timestamp:.
        [FAIL] FR24 Link: unknown ... failed!
        [FAIL] Receiver: down ... failed!
        [FAIL] FR24 MLAT: not running ... failed!

        Any advice?

        Comment


          #5
          Originally posted by nickkraal View Post
          So I ran the reconfigure command via command line. Everything went well until the end where there is this submitting form error now:
          ...
          ...
          Submitting form data...ERROR
          Invalid email provided!
          Would you like to try again?
          ....
          ....
          Yes, I checked configuration by command line "sudo fr24feed --reconfigure", and it gives same problem of "invalid email provided. Would you like to try again?", but log file is showing everything is ok. Checked my stats page https://www.flightradar24.com/accoun...stats/?id=xxxx, and stats are updating.

          TRY:
          Code:
          sudo fr24feed --signup

          Comment


            #6
            Thanks for this advice. I actually reinstalled fr24feed and this this is why you probably saw that the stats were updating.

            I ran the "sudo fr24feed --signup" command and chose "No" for "Would you like to use autoconfig (*yes*/no)" and enter the manual configuration settings in. Checking the fr24feed status:

            $ sudo service fr24feed status
            [ ok ] FR24 Feeder/Decoder Process: running.
            [ ok ] FR24 Stats Timestamp: 2016-07-22 16:50:55.
            [ ok ] FR24 Link: connected [UDP].
            [ ok ] FR24 Radar: T-OMDW6.
            [ ok ] FR24 Tracked AC:.
            [FAIL] Receiver: down ... failed!
            [FAIL] FR24 MLAT: not running ... failed!

            https://www.flightradar24.com/accoun...stats/?id=xxxx showed an "offline" status.

            So I ran the "sudo fr24feed --signup" command again and chose "Yes" for "Would you like to use autoconfig (*yes*/no)". Checking the fr24feed status now shows:

            $ sudo service fr24feed status
            [ ok ] FR24 Feeder/Decoder Process: running.
            [ ok ] FR24 Stats Timestamp: 2016-07-22 16:56:18.
            [ ok ] FR24 Link: connected [UDP].
            [ ok ] FR24 Radar: T-OMDW6.
            [ ok ] FR24 Tracked AC:.
            [ ok ] Receiver: connected (2 MSGS/0 SYNC).
            [ ok ] FR24 MLAT: ok [UDP].
            [ ok ] FR24 MLAT AC seen: 0.

            https://www.flightradar24.com/accoun...stats/?id=xxxx showed an "online" status.

            Below is the seemingly working configuration:

            fr2345.jpg

            Comment


              #7
              Having the same problem as you, not being able to activate raspberry pi. If I check my status it says online and it's been collecting and send data just fine.

              Comment


                #8
                I have a problem nearly similar to the above stated one.

                Preliminary remarks:
                Since nearly 2 years I am feeding FR24 als follows: DVB-T-Stick, Windows Notebook, dump1090 (Malcolm Robb), FR24-feeding-software. Running fine.
                Now I bought a RPi 3 Model B to feed FR24 from now on from the Rpi and no more from the Notebook.

                Although I am a RPi-Newbie and also not a linux/raspbian specialist, all setups obviously worked fine, as one can see:
                1) FR24-feeder-setup via SSH...
                -> $ sudo bash -c "$(wget -O - http://repo.feed.flightradar24.com/install_fr24_rpi.sh)"
                ...finally displayed these 3 lines:
                Saving settings to /etc/fr24feed.ini...OK
                Settings saved, please run "sudo service fr24feed restart" to use new configuration.
                Installation and configuration completed!

                2) Then Feeder-Restart:
                $ sudo service fr24feed restart

                3) Feeder Status...
                $ sudo service fr24feed status
                ...displays:
                * fr24feed.service - LSB: Flightradar24 Decoder & Feeder
                Loaded: loaded (/etc/init.d/fr24feed)
                Active: active (running) since Fr 2016-10-28 12:33:02 CEST; 2h 59min ago
                Process: 555 ExecStart=/etc/init.d/fr24feed start (code=exited, status=0/SUCCESS)
                CGroup: /system.slice/fr24feed.service
                |-686 /usr/bin/fr24feed -- --monitor-file=/dev/shm/fr24feed.txt --...
                `-707 /usr/lib/fr24/dump1090 --net --fix --raw --mlat

                Okt 28 12:33:02 raspberrypi fr24feed[555]: Starting FR24 feeder: fr24feed.
                Okt 28 12:33:02 raspberrypi systemd[1]: Started LSB: Flightradar24 Decoder &....
                Hint: Some lines were ellipsized, use -l to show in full.

                ...which also seems to be normal and OK.

                BUT:
                $ tail -f /var/log/fr24feed.log
                ...SHOWS this loop:
                2016-10-28 15:36:08 | [mlat][i]Terminating connection
                2016-10-28 15:36:09 | [mlat][i]Configuring UDP connection udp://mlat-1.fr24.com:19788
                2016-10-28 15:36:09 | [mlat][i]Registering MLAT station
                2016-10-28 15:36:09 | [mlat][i]Registering MLAT station: SUCCESS
                2016-10-28 15:36:13 | [feed][i]sent 0,5 AC
                2016-10-28 15:36:19 | [feed][i]sent 0,3 AC
                2016-10-28 15:36:24 | [feed][i]sent 0,6 AC
                2016-10-28 15:36:25 | [mlat][i]No ADS-B time reference available (0/2)
                2016-10-28 15:36:29 | [feed][i]sent 0,5 AC
                2016-10-28 15:36:34 | [feed][i]sent 0,4 AC
                2016-10-28 15:36:39 | [feed][i]sent 0,3 AC
                2016-10-28 15:36:41 | [mlat][i]No ADS-B time reference available (0/1)
                2016-10-28 15:36:41 | [mlat][i]Pinging the server
                2016-10-28 15:36:41 | [mlat][w]Could not ping MLAT server, result=-1000, number of errors=1
                2016-10-28 15:36:44 | [feed][i]sent 0,4 AC
                2016-10-28 15:36:49 | [feed][i]sent 0,3 AC
                2016-10-28 15:36:54 | [feed][i]sent 0,3 AC
                2016-10-28 15:36:57 | [mlat][i]No ADS-B time reference available (0/1)
                2016-10-28 15:37:00 | [feed][i]sent 0,4 AC
                2016-10-28 15:37:05 | [feed][i]sent 0,2 AC
                2016-10-28 15:37:06 | [feed][i]filtering out 5 overlapping AC (saving bandwidth)
                2016-10-28 15:37:10 | [feed][i]sent 6,2 AC
                2016-10-28 15:37:13 | [mlat][i]No ADS-B time reference available (0/0)
                2016-10-28 15:37:13 | [mlat][i]Pinging the server
                2016-10-28 15:37:14 | [mlat][w]Could not ping MLAT server, result=-1000, number of errors=2
                2016-10-28 15:37:14 | [mlat][i]Terminating connection
                2016-10-28 15:37:15 | [mlat][i]Configuring UDP connection udp://mlat-1.fr24.com:19788
                Note that the first two lines are identical to the last two lines. This sequence ist repeating and repeating and...

                A)
                Curious (in my Newbie eyes) seems: "Could not ping MLAT server".
                With SSH under user 'pi' I can ping...
                $ sudo ping mlat-1.fr24.com
                ...which answers:
                PING wro.fr24.com (83.140.21.66) 56(84) bytes of data.
                64 bytes from 83.140.21.66: icmp_seq=1 ttl=53 time=70.3 ms
                64 bytes from 83.140.21.66: icmp_seq=2 ttl=53 time=71.3 ms
                64 bytes from 83.140.21.66: icmp_seq=3 ttl=53 time=69.9 ms
                So obviously not a firewall problem.

                B)
                The message "No ADS-B time reference available" seems also strange, as every 5-10 minutes (or so) the following lines appear in the file fr24feed.log:
                2016-10-28 15:53:50 | [time][i]Synchronizing time via NTP
                2016-10-28 15:53:50 | [mlat][i]No ADS-B time reference available (0/2)
                2016-10-28 15:53:51 | [feed][i]sent 3,6 AC
                2016-10-28 15:53:54 | [time][i]Time synchronized correctly, offset +0.0004 seconds, drift -0.0000 seconds/minute
                So at least also NTP seems to work fine.

                Here my feeder settings:
                Feeder-Settings.jpg

                Any ideas? Thank you very much in advance. -Wolli-

                Comment


                  #9
                  i sugest you to change: receiver > avr/tcp and in host/ip > localhost:30002 save settings and restart, share your feedback.
                  cheers

                  Sent from my SM-N910F using Tapatalk

                  Comment


                    #10
                    Hi mrcarlos, and thank you very much for your reply.

                    I just tried your suggestions:

                    Attempt #1:
                    receiver > avr/tcp and host/ip > localhost:30002 - then stop and start
                    The feeder then produced error messages:
                    2016-10-30 12:02:49 | [reader][i]Connecting to AVR-TCP receiver via (avr-tcp://localhost:30002)
                    2016-10-30 12:02:49 | [reader][e]Could not connect to avr-tcp://localhost:30002


                    Attempt #2:
                    Additionally to the changes performed in attempt #1 I changed the field "RAW data (30002/30334)" to "YES" - then stop and start. Just to see what happens.
                    Result: The feeder produced the same error messages (of course new timestamps):
                    2016-10-30 12:07:00 | [reader][i]Connecting to AVR-TCP receiver via (avr-tcp://localhost:30002)
                    2016-10-30 12:07:00 | [reader][e]Could not connect to avr-tcp://localhost:30002


                    So now I performed a "fallback" to the "original" configuration (receiver: DVBT-stick - Host/IP: -empty-) - then stop and start.

                    BTW: When I switch MLAT off in the config (then stop and start), the feeder is running fine. So I think I don't have a basic problem here on my RPi.

                    Kind regards, -Wolli-

                    Comment


                      #11
                      After some to-and-fro mails with the FR24 support my problems are gone, without any changes on my side. MLAT is working now fine here since afternoon of 05-nov-2016.

                      Obviously there was a misconfiguration of the MLAT server mlat-1.fr24.com, not accepting the pings (see above log line "[mlat][w]Could not ping MLAT server"). This is my own assessment, as I received up to now no final report from FR24 support.

                      Here a snapshot from the feeder's log, with MLAT running, FYI:


                      2016-11-05 15:37:00 | [mlat][i]Configuring UDP connection udp://mlat-1.fr24.com:19788
                      2016-11-05 15:37:00 | [feed][i]sent 1,0 AC
                      2016-11-05 15:37:00 | [mlat][i]Registering MLAT station
                      2016-11-05 15:37:00 | [mlat][i]Registering MLAT station: SUCCESS
                      2016-11-05 15:37:05 | [feed][i]sent 4,0 AC
                      2016-11-05 15:37:06 | [mlat][i]Received ADS-B time references AC:
                      2016-11-05 15:37:06 | [mlat][i] 4CA5EC
                      2016-11-05 15:37:10 | [feed][i]sent 4,0 AC
                      2016-11-05 15:37:15 | [feed][i]sent 4,0 AC
                      2016-11-05 15:37:16 | [mlat][i]Pinging the server
                      2016-11-05 15:37:16 | [mlat][i]Stats 21/21
                      2016-11-05 15:37:20 | [feed][i]sent 4,0 AC
                      2016-11-05 15:37:25 | [feed][i]sent 4,0 AC
                      2016-11-05 15:37:30 | [feed][i]sent 5,0 AC
                      2016-11-05 15:37:35 | [feed][i]sent 5,0 AC
                      2016-11-05 15:37:37 | [mlat][i]Pinging the server
                      2016-11-05 15:37:37 | [mlat][i]Stats 28/7
                      2016-11-05 15:37:41 | [feed][i]sent 6,0 AC
                      2016-11-05 15:37:46 | [feed][i]sent 4,0 AC
                      2016-11-05 15:37:46 | [mlat][i]Received ADS-B time references AC:
                      2016-11-05 15:37:46 | [mlat][i] 4CA5EC
                      2016-11-05 15:37:51 | [feed][i]sent 4,0 AC
                      2016-11-05 15:37:56 | [feed][i]sent 5,0 AC
                      2016-11-05 15:37:56 | [mlat][i]Pinging the server
                      2016-11-05 15:37:56 | [mlat][i]Stats 130/102
                      2016-11-05 15:38:06 | [feed][i]sent 3,0 AC
                      2016-11-05 15:38:07 | [feed][i]filtering out 4 overlapping AC (saving bandwidth)
                      2016-11-05 15:38:12 | [feed][i]sent 0,2 AC
                      2016-11-05 15:38:16 | [mlat][i]Pinging the server
                      2016-11-05 15:38:16 | [mlat][i]Stats 241/111
                      2016-11-05 15:38:17 | [feed][i]sent 0,1 AC
                      2016-11-05 15:38:22 | [feed][i]sent 0,3 AC
                      2016-11-05 15:38:27 | [mlat][i]Received ADS-B time references AC:
                      2016-11-05 15:38:27 | [mlat][i] 4CA5EC
                      2016-11-05 15:38:28 | [feed][i]sent 0,2 AC
                      2016-11-05 15:38:34 | [feed][i]sent 0,2 AC
                      2016-11-05 15:38:34 | [feed][n]syncing stream async: 1
                      2016-11-05 15:38:35 | [feed][n]syncing stream result: 1
                      2016-11-05 15:38:36 | [mlat][i]Pinging the server
                      2016-11-05 15:38:36 | [mlat][i]Stats 241/0
                      2016-11-05 15:38:39 | [feed][i]sent 0,3 AC
                      2016-11-05 15:38:44 | [feed][i]sent 0,1 AC
                      2016-11-05 15:38:49 | [feed][i]sent 0,1 AC
                      2016-11-05 15:38:56 | [mlat][i]Pinging the server
                      2016-11-05 15:38:56 | [mlat][i]Stats 326/85
                      2016-11-05 15:38:56 | [feed][i]sent 2,1 AC
                      2016-11-05 15:39:01 | [feed][i]sent 0,2 AC
                      2016-11-05 15:39:06 | [mlat][i]No ADS-B time reference available (0/0)
                      2016-11-05 15:39:07 | [feed][i]sent 0,1 AC
                      2016-11-05 15:39:08 | [feed][i]filtering out 4 overlapping AC (saving bandwidth)
                      2016-11-05 15:39:12 | [feed][i]sent 4,1 AC
                      2016-11-05 15:39:17 | [mlat][i]No ADS-B time reference available (0/0)
                      2016-11-05 15:39:17 | [mlat][i]Pinging the server
                      2016-11-05 15:39:17 | [mlat][i]Stats 423/97
                      2016-11-05 15:39:17 | [feed][i]sent 3,2 AC
                      2016-11-05 15:39:20 | [feed][i]removed 1 of 9 AC
                      2016-11-05 15:39:23 | [feed][i]sent 0,2 AC
                      2016-11-05 15:39:26 | [mlat][i]Received ADS-B time references AC:
                      2016-11-05 15:39:26 | [mlat][i] 4CA5EC
                      2016-11-05 15:39:28 | [feed][i]sent 3,2 AC
                      2016-11-05 15:39:33 | [feed][i]sent 0,2 AC
                      2016-11-05 15:39:36 | [feed][i]removed 1 of 8 AC
                      2016-11-05 15:39:36 | [mlat][i]Pinging the server
                      2016-11-05 15:39:36 | [mlat][i]Stats 628/205
                      2016-11-05 15:39:38 | [feed][i]sent 2,1 AC
                      2016-11-05 15:39:44 | [feed][i]sent 2,1 AC
                      2016-11-05 15:39:49 | [feed][i]sent 3,0 AC
                      2016-11-05 15:39:52 | [feed][i]removed 1 of 7 AC
                      2016-11-05 15:39:55 | [feed][i]sent 3,0 AC
                      2016-11-05 15:39:56 | [mlat][i]Pinging the server
                      2016-11-05 15:39:56 | [mlat][i]Stats 628/0
                      2016-11-05 15:40:00 | [feed][i]sent 3,0 AC


                      That's, how it IMHO should look like, when MLAT is running correctly.
                      Last edited by Wolli; 2016-11-11, 17:58. Reason: mixed up date and log, corrected

                      Comment

                      Working...
                      X